How to Clean a Bore Snake

PDF download Download Article
PDF download Download Article

Bore snakes are used to clean guns' barrels. In order to do this effectively, you need to clean your bore snake, too. This can be done easily by either hand- or machine-washing. However, it's important to keep a few pointers in mind when doing so in order to keep your gun safe when you use your snake next.

Method 1
Method 1 of 3:

Washing by Hand

PDF download Download Article
  1. Start filling your sink, bucket, or other container with warm water and add a few drops of mild laundry detergent. Place your snake in the water. Let it soak for at least 15 to 20 minutes. For especially dirty or oily snakes, give it 30 to 40 minutes. [1]
  2. First, spin the snake around in the water to dislodge any loose dirt or oil. Then use a microfiber cloth to rub the braided floss part of the snake. Finally, use a toothbrush to gently scrub the bronze bore brush. Repeat as needed to remove all dirt and oil. Then rinse it under running water to remove all traces of soap. [2]
    Advertisement
  3. Use your non-dominant hand to hold the snake by one end so that it dangles over your sink, bucket, or other container. Use your dominant hand to gently squeeze the water out from top to bottom until you reach the bore brush. Skip that part and then continue in the same fashion for the rest of the snake's length. [3]
  4. Use a clean, dry cloth to pat the snake down. Sponge out as much water as you can. Then hang it over a drying rack or clothes hanger, or pin it to a clothesline to air-dry. [4]
    5. Advertisement
Method 2
Method 2 of 3:

Machine-Washing

PDF download Download Article
  1. Put your snake inside a wash bag, pillowcase or something similar. Tie it shut. Alternatively, roll the snake up and then tie it up with white shoelaces or a similarly light-colored machine-safe cord. Do not use the snake's pull cord to do this, since the knots may tighten during washing, which means you might have to cut the cord to undo your bundle. [5]
  2. First, set your washer to a small load on the delicate cycle. Start filling it with water and add a few drops of mild laundry detergent. Once the machine fills, switch it off. [6]
  3. Once the machine has filled, place the snake in the soapy water. If it isn't too dirty, give it 15 to 20 minutes to soak. Give it 30 to 40 minutes if it's very soiled. [7]
  4. Switch the machine back on once the snake has had a chance to soak. Let the cycle run to its end. [8]
  5. Once the cycle completes, take the snake out of its bag or remove its ties. Pin the snake to a clothesline or hang it over a clothes hanger or drying rack so it can air-dry.
    6. Advertisement
Method 3
Method 3 of 3:

Taking Precautions

PDF download Download Article
  1. Wait until your snake is totally dry to the touch before running it through your gun's barrel. Keep in mind that water can rust or otherwise damage your gun. Protect your gun by giving the snake the chance to totally air-dry before bringing the two into contact. [9]
    • Drying times will depend on the materials and size of your snake.
  2. If you're in a rush, it may be tempting to wipe the bore brush with the same cloth that you used for the rest of the snake. However, be aware that this will most likely result in fibers being left behind on the brush's bristles. These in turn will end up in your gun's barrel when you use the snake next, so definitely use a toothbrush in order to keep your barrel clean. [10]
  3. If you're machine-washing and choosing to roll your snake up and tie it into a bundle, never use dark-colored shoelaces or cords to do so. Expect these to possibly stain your snake during its wash. These stains will make it harder to judge what's dirt, what's oil, and what's just a stain. [11]
    4. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!

      Things You'll Need

      Hand-Washing

      • Sink, bucket, or other container
      • Water
      • Mild laundry detergent
      • Microfiber cloth
      • Toothbrush
      • Drying rack, clothes hanger, or clothesline

      Machine-Washing

      • Washing machine
      • Wash bag, pillow case, or white ties
      • Mild laundry detergent
      • Drying rack, clothes hanger, or clothesline

      You Might Also Like

      The Key Differences Between a King Snake and a Coral Snake
      How to
      Get Rid of Snakes
      How to
      Sex a Corn Snake
      How to
      Build a Relationship with Your Snake
      How to
      Trap a Snake
      How to
      Catch a Snake
      How to
      Hold a Snake
      How to
      Identify a Venomous Snake
      How to
      Tell the Difference Between a Milk Snake and a Coral Snake
      How to
      Feed a Snake Frozen Food
      How to
      Help Your Snake Shed
      How to
      Get Rid of Mites on Snakes
      How to
      Tame Snakes
      How to
      Feed a Corn Snake
      Advertisement

      References

      1. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      2. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      3. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      4. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      5. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      6. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      7. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      8. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      9. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      1. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html
      2. ↑ http://goneoutdoors.com/clean-boresnake-6702566.html

      About This Article

      Article Summary X

      To wash a bore snake, start by soaking it in a bucket or sink full of warm soapy water. Next, spin the snake around in the water to get rid of loose dirt. Then, wash it with a microfiber cloth and gently scrub the bronze bore brush with a toothbrush. Afterwards, squeeze all the air out of the snake and let it air dry completely before running it through your gun. For tips on how to machine wash your snake, keep reading!

      Did this summary help you?
      In other languages
      Thanks to all authors for creating a page that has been read 89,816 times.

      Did this article help you?

      Advertisement