How to Fix a Garden Hose

Last Updated: March 18, 2024

It's happened many times before: you pull your garden hose out from the garage, screw it onto the faucet, attach that spiffy nozzle you got from the hardware store, turned on the water, and got soaked as the leaky hose gushed water all over you. Instead of replacing that hose, consider some simple methods to mend it.

Steps

Download Article

If it didn't squirt you in the face, you may have to go on a hole hunt. Does your hose leak at the faucet? Does it leak where you've joined two hoses? Does it leak at the point where you've attached a sprinkler head or spraying device? Or does it leak somewhere in the middle? ^{[1]
X
Research source}
2
Fix leaky joints. Detach the hose from other hoses or devices, and thoroughly lube the threads of each with petroleum jelly.
- Reattach and you will notice fewer leaks, or even none at all. Be careful trying to reattach the items as your hands will be slick.
- Another option is to use a rubber washer. These are available at a hardware or garden supply store and can be slipped onto the "female" end of the hose. This should prevent leaking when it is joined to another hose or device. ^{[2]
  X
  Research source}
Advertisement
3
Use rubber cement for tears or punctures. ^{[3]
X
Research source}
- Using a dry paper towel, dry off the section of hose where there is a hole or cut. If the hole is within a foot (30 cm) of the end of the hose, try using a piece of dowel with paper towel wrapped around it to clean the inside of the hose.
- Apply some rubber cement to — and around — the hole. Fill in the hole, but not so much that it gets inside of the hose. This could result in clogging up the hose, and increasing the water's pressure, causing more leaks and an incentive for the hose to burst at that weak spot.
4
Use a tire puncture repair kit. These are most commonly sold at bicycle repair shops, body shops, car-part stores, etc. ^{[4]
X
Research source}
- Carefully read the directions of use, and apply the repair substance to the hole.
- After drying, buy a small sheet of solid rubber from a craft store, hardware store or other supplier. You can also cut a small square out of an old rubber rain boot, bicycle tire, or any other rubber item you no longer use.
- Glue it over the leak and let dry (use a glue able to keep the rubber attached strongly
5
Get a coupling for more severe tears. They are available at a hardware store. Repair couplings work by allowing you to cut out the leaky portion of hose and re-join it where you made the cuts. ^{[5]
X
Research source}
- Shutoff the water to the hose and cut out the bad portion.
- Splice in the repair coupling. It will have detailed instructions on the label.
Now go dry yourself off!

Community Q&A

Search

Add New Question

Question

How do I clean a black rubber garden hose so the black doesn't come off on my hands?

Community Answer

You can lightly sand the hose to remove the oxidized surface. Or, you can try painting it with an elastomeric paint, if the sanding doesn't work.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 8
Question

Can a garden hose be used like a snake to push a clog down a toilet?

Community Answer

Sort of, yes. You'd actually use a nozzle on the hose to let its water stream break up the clog. If the clog is deeper in the plumbing system, then just keep shoving the hose in while it's set to its strongest stream to flush out and break up anything in its path.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 3 Helpful 6
Question

How can I repair an expanding hose pipe when it is in the middle of the hose?

Community Answer

Visit the hardware store and pick up a joiner and some hose clamps. Then, cut out the bad section, loosely put the clamps on the hose, install the joiner into each pipe, and tighten the clamps. Be careful not to over-tighten the clamps though.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 11 Helpful 5

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Before trying to fix your hose, see if the store or supplier you bought it from will replace it for you. It always pays to keep your receipt.

Thanks
Helpful 10 Not Helpful 13

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

If you use "Super glue" or other strong adhesive, be very careful because it can really stick your fingers together or even your hands.

Thanks
Helpful 4 Not Helpful 5
Do not burn yourself with heat gun if you use one.

Thanks
Helpful 0 Not Helpful 4

Things You'll Need

Superglue
Tire repair kit
Rubber cement
Rubber square (from rain boot or purchased piece)
Hose splice kit
Rubber washers

You Might Also Like

[1]

[2]

[3]

[4]

[5]

Log in

How to Fix a Garden Hose

Steps

Community Q&A

Video

Tips

Warnings

Things You'll Need

You Might Also Like

References

About This Article

Reader Success Stories

Did this article help you?

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories