This article takes you through a step-by-step guide on how to clean, polish and lace your Dr. Marten's boots, whether they're black or cherry red. If you're after the "punk" or "battered" look with your boots this article is not for you; this is for the people who want nice and shiny boots. Everyone laces their boots differently. The way included in this article is one of the easiest for getting your boots on and off; it's also very aesthetically pleasing.

Part 1
Part 1 of 2:

Cleaning and Polishing Your Boots

  1. You don't want polish on them. If they're mucky then clean with washing up liquid and warm water. Then leave to dry. The white laces might need bleaching occasionally to keep them white, but they don't need cleaning every time. [1]
  2. You need a cold wet cloth and a bit of elbow grease for this. Try and avoid using soaps or hot water, these are no good for your leather. Just wipe the whole boot until it's clean; make sure you go inside where the tongue of the boot is. Dry with the dry side of the cloth. [2]
    Advertisement
  3. This step is the same for both red and black boots. Take your "wipe on" jay cloth, wrap it around your index finger on your strongest hand. Dab it inside of your tin of polish and start at the front (toe end) of your boot. Make little circles with your finger while applying a small amount of pressure.
  4. You can tell when it is all done because it goes "matte" and loses its shine. You will be able to tell if you missed a spot. Again, make sure you go in where the tongue is.
  5. Now's a good time to get started on a second or third pair to pass the time. Try and polish more than one pair at a time if you have them or have friends with a pair; it becomes a little system of polishing one while the others dry and your never having to wait.
  6. Take your "wipe off" jay cloth and do exactly the same thing as when putting the polish on, little circles starting from the toe. you should immediately see the shine coming through as you go. keep at it until the whole boot gleams. [3]
    Advertisement
Part 2
Part 2 of 2:

Lacing Your Boots

  • This is a "ska/rudeboy/scooterist" way of lacing.
  1. You could use a lighter to melt the frayed end into the knot to keep it permanent, but this is not necessary. If you do decide to do it please be careful, molten plastic is not something you want on your skin. light for a second and squish it down with something (not your finger). You should now have a lace with a knot on one end and the normal plastic bit on the other end. [4]
  2. You should start with the opposite eyelet when you lace the other boot to make it symmetrical. Pull through until the knot is against the inside of your bottom eyelet. [5]
  3. It needs to go from the inside, out.
  4. You can tie a slip knot to stop it loosening or just tuck the end in. [6]
  5. ! They are clean, shiny, laced up and ready to go and dance to some ska. Keep it rude.
    Advertisement

Expert Q&A

Ask a Question

      Advertisement

      Tips

      • Try and keep the polish away from your yellow stitching on your boot if you want to keep them yellow. [7]
      • Polish stains, really stains. Try and keep it away from anything fabric especially carpets and clothing.
      Advertisement

      Warnings

      • Lighters are dangerous. Do not use if you are under the legal age. Get an adult to help.
      Advertisement

      Things You'll Need

      • 2 yellow cotton jay cloths (one for polish on, one for polish off, think karate kid)
      • A wet dish cloth/wash cloth (this is the pink thing pictured, you could use almost anything for this, keep half dry for drying them)
      • Polish (for cherry reds, use burgundy kiwi and for black use, normal black kiwi)
      • At least 1 pair of Dr Martens


      About this article

      Thanks to all authors for creating a page that has been read 50,005 times.

      Did this article help you?

      Advertisement