Q&A for How to Locate a Leak in an Air Mattress

Return to Full Article

Coming soon

Add New Question

Question

What if I can't find the leak?

Community Answer

Use a thin, light plastic attached to a stick or hanger. Cut the plastic into thin strips away from the stick or hanger (the thinner the better, but not too long or short). Move it across an inflated mattress and the hole will be revealed when a strip blows away from the mattress.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 30 Helpful 116
Question

How can I repair the leak around the edge of the air valve?

Community Answer

A thick, well-applied layer of duct tape should do the trick.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 21 Helpful 16
Question

How do I find a leakage in an electric pump built-in on an air mattress?

Community Answer

Fully inflate the mattress. Bundle the cord in a tight, flat package with rubber bands and tape in place over the connection or stow it away in the recession provided. Use lightweight Saran Wrap and typical desk tape to install an airtight patch over the entire area. The plastic wrap bubble will be loose and it will be possible to press out excess air before putting on the last section of tape. Be sure to lightly burnish the tape with a fingernail to close any gaps. Any leak will at least fill out the looseness or slack in the plastic patch.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 7 Helpful 19
Question

How do I find a leak in an air mattress without getting it wet?

Community Answer

You can find it by listening for the leak while putting pressure on the mattress.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 24 Helpful 21
Question

How can I keep my air mattress from sliding?

Community Answer

Buy some of the non-slip material for rugs. Place one section of the material lengthwise across the head of the mattress, and another at the foot.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 11 Helpful 11
Question

What can I use to repair the tear in my air mattress?

Community Answer

You can buy some patches from stores or temporarily seal it with some Scotch tape.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 25 Helpful 13
Question

My air mattress inflates with an electrical cord. How do I check for leaks around the valve without damaging the cord?

Community Answer

Fully inflate your mattress. Bundle the cord in a tight flat package with rubber bands and tape it in place over the connection (or stow it away in the recession provided). Use lightweight Saran Wrap and typical desk tape to install an airtight patch over the entire area; the plastic wrap bubble will be loose, and it will be possible to press out any excess air before putting on the last section of tape. Be sure to lightly burnish the tape with a fingernail to close any gaps. Any leak will at least fill out the looseness or slack in the plastic patch.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 4 Helpful 4
Question

Should I turn off the switch once the mattress is inflated?

Community Answer

Yes, you should be sure to turn the switch off. Otherwise, it will over-inflate the mattress and it could cause the mattress to burst.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 3 Helpful 5
Question

What do I do if I can't find the hole in my air mattress?

Community Answer

Get someone to help you. Find a young person with excellent eyes and ears who might be able to detect the hole more easily. Have one person lie on the mattress, which exerts more pressure on the hole, while other person or persons look around the mattress very closely.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 5 Helpful 3