How to Remove Water Heater Elements

Removing water heater elements can be a very difficult task. In most cases you will need to use a Water Heater Element Removal Wrench.

Steps

  1. Careful there may be two separate breakers to the water heater.
  3. (see Tips below)
  4. Usually one or two easily accessible screws hold them on.
  5. It may be fiberglass or a piece of cardboard.
  6. (SEE TIPS BELOW)
  11. (SEE TIPS BELOW)
  13. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Will there be air in the hot water line?
    Community Answer
    Yes, but if you run the water for a few minutes, it should release all of the air in the lines.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 0 Helpful 6
  • Question
    Can I set it without draining water?
    Community Answer
    Yes. It is tricky, but possible. First, make sure you have turned the electricity off and that the water in the cylinder is cold. Stop the water from the main water stop cock, open a hot tap, and leave it open to drain any water left on the pipework and in the expansion vessel. Then, disconnect the hot outlet pipe from the cylinder. Through that hole, you can feed an inspection camera connected to your phone so that you can view it and asses its condition visually. After you are done, reconnect the hot outlet pipe, turn off the hot tap, open the main water stopcock, and then open the hot tap again to get out any trapped air. Now, go back to the cylinder and check for any leaks.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 0 Helpful 5
  • Question
    What size is the nut on the end of the element?
    Community Answer
    The elements come with a nut and a tool to remove them, so you don't need to know exactly. Take your info on the heater with you and you'll get the "gadget" that comes with the element to remove the element and replace!
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 9 Helpful 5
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit

      Advertisement

      Video

      Tips

      • Sometimes tightening the element (turning it clockwise) a small amount could help loosen it for removal.
        Thanks
        Helpful 1 Not Helpful 0
      • You may want to write down what the pattern is from the old element to the new element. You don't want to mix the wires up.
        Thanks
        Helpful 1 Not Helpful 1
      • If the heater element is stuck, there are three ways to proceed. 1. Heat the element with a propane torch and see if that loosens it. 2. Refill the tank partially so the tank doesn't move when trying to twist the element. 3. If all fails, use hammer to remove terminals and plastic end of element > on the newly exposed surface of the element, drill and tap two 1/4" holes into element > keep holes close to center of element so not to damage the element threads > twist two long 1/4" bolts into holes > use a wrench or vice grips to grab the two bolts and twist to remove element. 4. If you are having trouble removing the element, try repeatedly tapping on the element with a small hammer to break the corrosion loose.
        Thanks
        Helpful 0 Not Helpful 0
      Show More Tips
      Advertisement

      Warnings

      • The metal jacket on a hot water heater is deceptively sharp.
        Thanks
        Helpful 8 Not Helpful 3
      • The elements usually come with washers, if you replace them - remember to put the washer on the element.
        Thanks
        Helpful 5 Not Helpful 4
      • If you are unsure how to turn the power off or check if the power is off to the heater, consult a professional.
        Thanks
        Helpful 5 Not Helpful 6
      • Be sure you check the seat in the tank where the element gasket is going to seat. Be sure it is clean and free from any rust pits. Otherwise it will leak.
        Thanks
        Helpful 5 Not Helpful 6
      Advertisement

      Things You'll Need

      • Screwdriver
      • (Optional) Element Wrench
      • Smaller water heaters (ie: 17 gal) may need a very small wrench.

      You Might Also Like

      How to
      Make Coffee
      How to
      Become Taller Naturally
      Advertisement
      How to
      Improve Your Alexa Ranking
      The Best Couples Halloween Costumes for 2021
      How to
      Slim Your Face
      How to
      Start a Vegetable Garden
      How to
      Reduce Plastic Use
      How to
      Make Homemade Pasta
      How to
      Find Things You Lost
      How to
      Be a Cholo
      How to
      Organize Your Schedule
      How to
      Iron
      How to
      Do Drywall Repair
      How to
      Dress for a Night at the Casino
      Advertisement

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about water heating systems, check out our in-depth interview with David Balkan .

      About this article

      Thanks to all authors for creating a page that has been read 237,761 times.

      Did this article help you?

      Advertisement