PDF download Download Article PDF download Download Article

Is the water pressure in your home just barely a trickle? Or, maybe the pressure is too high, and it’s causing issues with your appliances. Fortunately, adjusting the water pressure in your home is easy to do yourself, and it only requires a few tools that you probably already own. In this article, we’ll tell you exactly how to adjust your water pressure regulator for the perfect water pressure in your home.

1

Find the water pressure regulator on your supply line.

PDF download Download Article
  1. Usually, this line comes in through the basement or the crawlspace, or wherever your water heater is stored. The water pressure regulator is a bell-shaped piece of hardware that’s attached to the main water line. [1]
    • The water pressure regulator is used to lower the water pressure as it comes into your home. Most urban water lines start at 150 to 200 pounds per square inch (psi), which is way too much pressure for a residential home.
  2. Advertisement
2

Check out the specifications on the water pressure regulator.

PDF download Download Article
  1. After you find the water pressure regulator, take a moment to read the label on the side or the back. Write down the optimal psi, which is usually between 40 and 60. This will give you a guideline for how low or high you want to adjust your own water pressure. [2]
    • Setting your water pressure too high can lead to leaking pipes and even explosions. Be sure your water pressure stays within the optimal psi to avoid any damages to your home.
3

Attach a water pressure gauge to an outdoor faucet.

PDF download Download Article
  1. You can buy a water pressure gauge online, or you can find them at your local hardware store. Attach the gauge to a threaded faucet, like an outdoor hookup or a utility sink. Run the tap for about 30 seconds, and then write down the pressure on the gauge. [3]
    • For residential homes, optimal water pressure is usually between 40 to 50 psi. If yours is above 50, you can lower it; if it’s below 50, you can raise it.
  2. Advertisement
4

Loosen the locknut with a wrench.

PDF download Download Article
  1. Take a look at the water pressure regulator: you’ll notice a locknut at the very top. Grab a wrench or a pair of pliers and turn the locknut clockwise to loosen it. [4]
    • Old locknuts tend to loosen over time. If you notice that your water pressure is really high, it may be because your locknut is loose. You can replace it with a new locknut to tighten your adjusting bolt if you need to.
5

Turn the bolt clockwise to increase the pressure.

PDF download Download Article
  1. If your goal is to increase your water pressure, grab a wrench and place it around the adjusting bolt. Turn it clockwise in short quarter turns to adjust the pressure little by little. [5]
    • It’s better to adjust slowly than trying to increase the pressure too quickly. You can always go back and increase the water pressure more if you need to.
  2. Advertisement
6

Turn the bolt counterclockwise to reduce the pressure.

PDF download Download Article
  1. Place your wrench around the adjusting bolt, then slowly tighten it in quarter turns to reduce your water pressure. Go slowly to adjust the pressure little by little. [6]
7

Check the water pressure gauge again.

PDF download Download Article
  1. Once you’ve made your adjustments, head back to the tap that has your water pressure gauge and run the water for about 30 seconds. If your pressure is where it needs to be, then you’re good to go! [7]
    • If you need to make a few more adjustments, turn the tap off and use your wrench to tighten or loosen the adjusting bolt again.
  2. Advertisement
8

Tighten the locknut to secure the water pressure regulator.

PDF download Download Article
  1. Once your water pressure is right where you want it to be, use a wrench or pliers to turn the locknut counter clockwise to tighten it again. Keep turning the locknut until it just barely touches the top of the adjusting bolt to keep it in place. [8]
    • Pressing the locknut and the bolt head too close together can damage them.
9

Call a professional if your water pressure doesn’t change.

PDF download Download Article
  1. Sometimes, low or high water pressure can indicate a problem within your water main. If you’ve adjusted your water pressure regulator and it fluctuates, drops, or raises on its own, call a plumber to come out and take a look. [9]
    • You may also need to replace your water pressure regulator. A professional can determine how old it is and if it needs to be replaced.
  2. Advertisement


Expert Q&A

Ask a Question
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about water pressure, check out our in-depth interview with Dave Jones .

      About This Article

      Thanks to all authors for creating a page that has been read 113,791 times.

      Reader Success Stories

      • Anonymous

        Oct 23

        "Thank you. Over 28 years with incoming high pressure water problem. Now I know which one to turn that way."
      Share your story

      Did this article help you?

      Advertisement