Download Article
Download Article
The saxophone is a fairly easy instrument to put together, especially once you get the hang of attaching the reed. There are delicate pieces on the instrument, so you have to be careful about how much pressure you use while handling it and pushing the parts together. Start by assembling the mouthpiece, and then move on to connecting the larger pieces.
Steps
-
Moisten your reed by placing it on your tongue. Place one end of the reed in your mouth and allow your saliva to moisten it for about a minute. Then turn the reed around and moisten the other end in your mouth for a minute. Be careful not to cut your tongue since reeds sometimes have sharp edges.- You could also just soak the reed in a cup of water for a couple of minutes.
-
Line up the curved tip of the reed with the curved tip of the mouthpiece. Take the reed out of your mouth and place its flat side against the flat part of the mouthpiece. The thin, curved end of the reed should line up exactly with the thin, curved tip of the mouthpiece. [1] X Research source- If it's not lined up properly, the saxophone will make a squeaking noise when you blow air through it.
Advertisement -
Slide the ligature onto the mouthpiece and over the reed. Make sure that the wider end of the ligature slides on first to match the shape of the mouthpiece. Hold the reed in place with your thumb while you line the ligature up with the widest part of the mouthpiece. If the ligature is too tight to fit over the reed, loosen it by turning the screws counterclockwise.- The screws should be on the thick bottom part of the reed.
- A little bit of the reed will extend past the bottom of the ligature.
-
Tighten the ligature by twisting the screws. Still holding the reed in place with your thumb, use your other hand to tighten the ligature. Turn the screws clockwise until you feel a little bit of resistance. It should be just tight enough that the reed can no longer move around. Do not tighten past this point since you could damage the reed. [2] X Research source
Advertisement
-
Put the neck strap around your neck. Let the neck strap rest around your neck like a necklace. Make sure the hook is hanging over your chest at the front of the strap. Wait to make adjustments to its length until you have the saxophone attached to it. -
Apply cork grease to the saxophone neck as needed. Occasionally you’ll need to rub a little bit of cork grease onto the cork part of your saxophone’s neck. Apply a very small amount all the way around the tip of the cork whenever the mouthpiece stops sliding onto the neck easily.- You can get tubes of cork grease at music stores or online.
-
Twist the fully assembled mouthpiece onto the neck. Use a gentle, back-and-forth twisting motion to get the mouthpiece onto the neck of the sax. Twist it on until it’s about halfway down the length of the cork. The flat side with the reed on it should face down toward the inside of the neck.- If you’re having trouble getting it on, and you’ve already applied cork grease, don’t force the parts together. Take it to a repair shop to have it looked at by a professional. [3] X Research source
-
Pick up your saxophone by the bell. Picking up your sax by the upper body can cause damage to the mechanisms that make the instrument work properly. Wrap your fingers around the outside of the bell, where there are no keys, and grip this area as you lift it. -
Hook the neck strap onto the small loop on the back of the body. Below the octave key, about halfway down the saxophone, there’s a small metal loop. Connect the neck strap to this loop by opening the hook and fastening it over the loop. -
Slide the neck into the body. Using the same back-and-forth twisting motion, press the neck down into the body until it’s all the way on. The tip of the mouthpiece should line up perfectly with the rest of the horn and create one straight line from the reed to the bell. [4] X Research source- If you can’t slide the neck right into the body, try loosening the wing nut at the top of the body by turning it counterclockwise.
- Do not force the neck on. Consult a repair shop if you’re having difficulty getting the pieces together.
- Be careful to not damage the octave key built onto the neck when you’re assembling.
-
Adjust the neck strap as needed. Hold the assembled saxophone in front of you and loosen your grip on it so that the neck strap bears most of the weight of the instrument. If the mouthpiece is suddenly lower than you mouth, adjust the neck strap up. If it’s higher than your mouth, adjust the neck strap down. The strap should hold the saxophone exactly where it will be while you’re playing it.
Advertisement
Community Q&A
Search
-
QuestionHow far should reed be on the mouthpiece?PurpleOreoCommunity AnswerPut it far enough that you can see about a hair's-width of the mouthpiece at the top of the reed.
-
QuestionDo I blow out or suck in to make noise?Community AnswerBlow out! Blowing over a reed causes a certain airflow that makes noise.
-
QuestionHow do you hold the saxophone?Community AnswerTo hold it during assembly, hold it by the bell. To learn how to hold it while playing, consult the Wikihow article "How to Play the Alto Saxophone"
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
References
About This Article
Article Summary
X
To assemble a saxophone, line up the curved tip of the reed with the curved tip of the mouthpiece, then slide the ligature onto the mouthpiece and twist the screws to tighten it. Next, twist the assembled mouthpiece onto the saxophone's neck using a gentle, back-and-forth twisting motion. Then, pick up your saxophone by the bell and slide the neck piece into the body. Finally, adjust the neck strap until you feel comfortable holding the sax! For tips on greasing the neck, read on!
Did this summary help you?
Thanks to all authors for creating a page that has been read 195,265 times.
Reader Success Stories
- "The instructions were clearly stated in a step by step fashion without any extraneous information. Illustrations were simple and informative, exactly what the novice needs. It's unnecessary to get into any lengthy descriptions with such a process." ..." more
Advertisement
"The instructions were clearly stated in a step by step fashion without any extraneous information. Illustrations were simple and informative, exactly what the novice needs. It's unnecessary to get into any lengthy descriptions with such a process."
..."
more
"I'm a beginner, and intimidated by the mechanisms - didn't want to damage anything. Now I know!"
"This is going to help me a lot, because I just got it at school today."
"It helped me a lot, thank you!"
