Download Article
Download Article
A blind hem stitch is a classic way to tailor trousers or skirts to the right length. This barely-visible hem creates a crisp, clean appearance and is easy to do with just a bit of practice. Many sewing machines have a special foot for blind hems, but you can make the stitch on a machine even without this attachment. Once you master the process, you'll find yourself spending a lot less on alterations!
Steps
-
Remove the seam from the existing hem. You can do this with a seam ripper or small nail scissors. Or, if the garment is much longer than desired, you can cut off the bottom with fabric scissors.
- Don't make the garment too short, though! Leave several inches to prepare your blind hem.
-
Try on the garment (right side out) in front of a full-length mirror and decide on a desired length for the hem.
- Stand on a stool or table and ask a friend to put a few pins at the correct level.
Advertisement -
Remove the garment and mark the desired hemline around the leg or skirt. Remove the pins.
- Use water-soluble pencil, pen, or chalk.
- Alternatively, you can mark the hemline with pins.
-
Decide how deep you want your hem, and mark a line that distance above and below the hemline. For example, if you want a 2-inch deep hem, you mark a line 2 inches (5.1 cm) above and 2 inches below the hemline.- Again, you can use a water-soluble pen or pencil, or do this with pins.
-
Trim the raw edge, leaving about 1 inch (3 cm) below your lowest line. Be certain to leave an inch of fabric!
-
Fold the raw edge in and press with an iron. If you have 1 inch (2.5 cm) of raw edge, tuck 1/2 inch (5.1 cm) of fabric under, leaving the remaining 1 ⁄ 2 inch (1.3 cm) under your bottom line.
- Some experts suggest sewing this fold with a basic straight stitch or finishing the raw edge with an over edge or zigzag stitch, but this may not be an essential step. [1] X Research source
-
Tuck the fabric under along the middle line so that it now forms the hemline. Do this by pinching the fabric at the middle line (what's to be your final hemline). Your other two lines (above and below the hemline) should line up, since they are equidistant from the hem. Pin around the hem to hold this fold in place.
-
Cuff the hem by folding along the line above the hem and pin. At this point, your bottom line will once again be exposed, and below it the pressed raw edge.
- You can remove the previous pins and use them to secure the folds.
-
Press the folds lightly with an iron. After you've done this, you can remove the pins if you wish, but it isn't necessary. [2] X Research source
Advertisement
-
Check that your sewing machine has a blind hem presser foot in its collection. The sewing machine requires a specific foot for this stitch, with the vertical bar passing between the two feet.
- Alternatively, buy a universal blind hem presser foot for your machine in a sewing shop or online. These feet are fairly inexpensive and a good choice if your machine does not have the blind hem presser foot. [3] X Research source Make sure, however, that it fits your machine. Check the product specifications before buying: they'll usually say which machines it works with.
- If you can't find a presser foot for your machine, you can still make this hem! Skip to sewing instructions in Part 3, Step 2.
-
Attach the blind hem presser foot to the sewing machine. Follow the instructions for your particular machine.
-
Set the machine to the blind hem stitch setting. This setting is often indicated by two stitches spaced far apart, but check your user's manual to be sure. Now you're ready to sew! [4] X Research source
Advertisement
-
Turn the fabric wrong side up (inside out, in other words) and position it on the sewing machine. Make sure the foot's vertical plate is sitting right on top of the fold. The machine is going to stitch along the raw edge section mostly, but cross the plate into the fold every few stitches.
-
Stitch slowly. Hold the fabric carefully so that the fold stays just under the vertical plate. This way the needle is sure to catch it. [5] X Research source If you do not have a blind hem presser foot, make the stitch pattern manually:
- Put the machine feed dogs on the inside.
- Place your fabric on the machine as in Step 1.
- Make five straight stitches, and then one stitch to barely catch the fold.
- Continue around the hem.
-
Inspect your work. Remove the garment, snip the thread, and turn right side out. Check for any missed stitches.
- If needed, go back and redo the sections where there is a missing stitch.
-
Remove the pins and press the hem. If a line remains from the previous hemline, try spritzing it with a bit of distilled water and ironing. If this doesn't work, it will probably come out when laundered. [6] X Research source
Advertisement
Expert Q&A
Search
-
QuestionHow do you blind stitch fabric that is really thick?Essie Karimi is a Professional Tailor and the Owner of Sew Fit Tailoring & Alterations, a sewing shop that has been operating for over 40 years. Essie specializes in tailoring, alterations, sewing, repairs, and redesign. Essie works on a variety of clothing types, including wedding dresses, formal wear, casual wear, sportswear, swimwear, and uniforms.Use a needle and thread! Thick fabric can cause the needle to break when you're using a machine.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- It is best to practice on scraps of fabric before hemming your item of clothing; this way you can perfect your technique without damaging your pants or skirt.Thanks
- Always read and follow the instructions for your sewing machine.Thanks
- The blind hem stitch is perfect for curtains, as well.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
References
- ↑ https://www.youtube.com/watch?v=zP6zhTCmR5M
- ↑ http://www.coletterie.com/tutorials-tips-tricks/tutorial-how-to-sew-a-blind-hem
- ↑ http://www.makeit-loveit.com/2011/07/blind-hem-stitch-with-a-sewing-machine.html
- ↑ http://www.coletterie.com/tutorials-tips-tricks/tutorial-how-to-sew-a-blind-hem
- ↑ http://www.coletterie.com/tutorials-tips-tricks/tutorial-how-to-sew-a-blind-hem
- ↑ http://www.coletterie.com/tutorials-tips-tricks/tutorial-how-to-sew-a-blind-hem
About This Article
Article Summary
X
To blind hem stitch, first remove the seam from the existing hem. Next, mark or pin the newly desired length for the hem. Trim the raw edge, leaving 1 inch below your lowest line, then fold the edge in and press it with an iron. After ironing, pin around the fold to hold the new hem in place. Attach the blind hem presser foot to your sewing machine, turn your garment inside out, and slowly stitch your hem. For tips on how to finish your hem without the blind hem presser foot attachment, keep reading!
Did this summary help you?
Thanks to all authors for creating a page that has been read 82,993 times.
Reader Success Stories
- "Very clear instructions. Thank you for using a thread we can see for the example!"
Advertisement
"Very clear instructions. Thank you for using a thread we can see for the example!"
