How to Build a Flag Display Case

PDF download Download Article
PDF download Download Article

This article explains how to build a flag display case that can be used to safely house and display valuable flags.

Steps

PDF download Download Article
  1. 3x5, 4x6, 5x9 (burial).
    • You will need the bottom (horizontal) measurement along with the two diagonal measurements. Also, get the thickness of the folded flag.
      • For this example we will use the 5x9 burial--
        • bottom msmt: 24"
        • diagonal msmt: 16-3/4"
        • thickness: 2-3/4"
    Advertisement
  3. Hardwoods are a better choice for this project. This is for reasons of visual appeal and longevity. For this example, we will use oak.
    • A 1x4 piece of oak actually measures 3 1/2" in width, which is fine.
      • Buy an 8 foot (2.4 m) length (for beginners, in case there are mistakes).
  4. You can do this with a circular saw or a chop saw (miter saw). [1] Chop saws give a much better cut. [2]
    • The bottom measurement of the flag is 24", so the inside measurement of the 45 degree cuts must be at least 24". I recommend cutting the length of 1/4. (little play room for glass and flag).
    • You should have approx. 6 feet (1.8 m) of board left. As you know, wood has a grain pattern. What follows now will give your case more of a professional look.
  5. of the angled 6' board (that's your long point of that particular angle, the other is the short point of that particular angle).
    • Your angled measurements are 16 3/4", short point to short point. However, you will be cutting it 3" longer than that (for mistakes), so lets just cut our side pieces 20" long. short to short.
    • Measure off the 6' board from long point 20". Using a speed square or framing square, make a mark and cut your piece. (set this piece aside)
    • The longer remaining piece should have a short point.
    • Once you do this, your two 45 degree angles at the top of the display case will fit and the grain will match. it will look continuous. (Match up all the angled pieces until you find that grain match).
    • When you place the bottom piece up to the angled side pieces to form the triangle, you will notice that the side pieces are too long. Just pencil mark the bottom where it hangs over the bottom piece. That now is going to be cut at a 45 degree. Make sure you cut the 45 degree angle the correct way, your end product should be a short to short angled piece. If it helps; when you are marking the piece to be cut, also mark the side of the board so you know for sure, which way the wood should be cut.
  8. [3]
    • We can measure the glass in two ways:
      • The exact size, minus 1/8th inch. (if there is going to be a wooden corner cover over the glass and attach it to the frame.) or
      • We can measure the glass 1/4" larger if we are going to insert it into the frame.
        • Buy an 8' piece of wooden corner board (for outside corners of walls) it is 3/4" long on each side of the 45 degree angle. Cut this to fit the outside of the triangular frame you just made. You can insert the glass from the back side after the glass is inserted, then you can cut and place 3 pieces of 1/4" x 1/4" moulding on the inside to hold the glass in place.
        • Inset glass involves using a table saw. If you have one or can use one, this is what you do. [4]
    • You set your guide that's on the table saw to 1/4" from the inside of the saw blade to the guide itself.
    • Set the depth of the blade to 1/8th inch.
      • If you know at the beginning that you will be insetting the glass, then cut the entire 8' length of board at one time. It's very difficult to cut small pieces like this and have it turn out correctly.
        • If you have never used a table saw, ask someone that has to preform this next step.
  9. making sure not too force the cut. be gentle. its wise to use a forked stick to push the wood through its cutting process.
    • There are jigs out there that can be purchased for just this job. Call a do-it-yourself place. they can help you.
    • Once you have your cuts made, you are ready to nail it together.
  10. Use small trim nails (1 1/4) long and nail frame together, with glass inserted into the cut grooves you just made (set nails with punch and color putty when done).
    • This is much easier done if you have a brad gun. Also place the frame so the glass is face down, so it doesn't break if it falls out during this process.
  12. (stain edges with proper color. For oak, you can use minwax-colonial maple or early American.)
  13. (on the back side) for screws.
    16. Advertisement

Video

Community Q&A

Search
Add New Question
  • Question
    The top corner is a 90-degree angle, so the ends of the pieces should each get a 45-degree cut, but the bottom two angles themselves are each 45 degrees, therefore the cut must be half of 45 degrees, correct?
    Community Answer
    The 90-degree angle at the top is made with two 45-degree cuts. The 45-degree angles at the bottom edges are each made with two 22.5-degree cuts.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 11 Helpful 22
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!

      You Might Also Like

      How to
      Dispose of a Damaged American Flag
      How to
      Fold an American Flag
      Best Ways to Celebrate Flag Day
      Why People Fly the Black American Flag and What It Means
      The Meaning of a Black and White American Flag
      How to
      Draw the Flag of the United States
      Proper Ways to Display the American Flag with Other Flags
      3 Ways to Make a Homemade Flag
      How to
      Make Your Own Flag Pole at Home
      How to
      Hoist a Flag
      How to
      Design Your Own Flag
      How to
      Fold a Flag Into a Triangle
      How to
      Draw the Canadian Flag
      How to
      Draw the Indian Flag
      Advertisement

      References

      1. ↑ https://www.familyhandyman.com/tools/miter-saws/how-to-use-a-power-miter-saw/
      2. ↑ https://www.youtube.com/watch?v=CjA7afRebFc
      3. ↑ https://www.youtube.com/watch?v=orqASac-P4g
      4. ↑ https://www.bobvila.com/articles/how-to-use-a-table-saw/
      5. https://www.woodworkersjournal.com/making-memorial-flag-case/
      6. http://www.militaryflagdisplaycase.com/buildingaflagdisplaycase.html Source of original article. Submitted by the Author.

      About This Article

      Thanks to all authors for creating a page that has been read 239,344 times.

      Did this article help you?

      Advertisement