PDF download Download Article PDF download Download Article

Electric shavers are incredibly convenient. They cut down shaving time drastically, and are more portable than a manual razor, shaving cream and aftershave. However, an electric shaver does require a bit more upkeep and maintenance to keep it performing at its best. You need to know how to disassemble the shaver for cleaning, and the cleaning process itself is much more involved than for a manual razor.

Part 1
Part 1 of 3:

Disassembling the Shaver

PDF download Download Article
  1. Since you’ll be cleaning hair and dead skin cells out of your shaver, you may not want to do it over a floor. Cleaning your shaver over your sink will allow you to easily get rid of fallen hairs and skin with just a bit of water.
  2. Some shavers have an on/off switch, whereas others have a switch you depress to activate the blades. Either way, make sure it isn’t running; you want to make sure there is no electric current running through the shaver before you begin. If water gets into the shaver, it could cause electrocution or damage the shaver.
    • If your electric shaver is battery powered, you may want to remove the batteries before cleaning it. [1]
    Advertisement
  3. Watermark wikiHow to Clean an Electric Shaver
    While models will vary, most will have a snap off head. [2] There should be a small clip at the bottom of the head; press on this with your finger and it should come free. Generally, this is the only disassembly required.
    • Electric shavers usually fit one of two categories: rotary or foil shavers. The disassembly is a bit different for each category, so refer to your shaver’s instruction manual for details.
    • Be careful with the pieces you remove from the shaver. Some are incredibly sensitive and shouldn’t be cleaned. Refer to the owner’s manual to know how far you should disassemble the shaver and what you should be cleaning. [3]
  4. Since you’re about to clean it, you should take a moment to make sure there aren’t any cracks in the casing or damage to the shaver head, such as nicks in the blades. If you can see any seals or gaskets, make sure to inspect them for damage. [4]
  5. Advertisement
Part 2
Part 2 of 3:

Cleaning the Shaver

PDF download Download Article
  1. Watermark wikiHow to Clean an Electric Shaver
    Hold the shaver at an angle, the head pointed downwards over your sink. With one finger, tap the side of the shaver firmly. Tapping repeatedly will shake most of the the hair loose. Keep doing this until you don’t see any hair falling out. [5]
    • Avoid tapping the shaver against the sink; the impact of the hard porcelain could damage the shaver’s more sensitive parts. [6]
  2. Watermark wikiHow to Clean an Electric Shaver
    Most electric shavers come with a micro-bush specifically designed for cleaning it. After removing the shaver head, you should be able to reach the mechanisms that a hair could get lodged into. Brush gently, to make sure you’re not causing any scratches or scuffs.
    • If your shaver didn’t come with its own brush, you can use a small paintbrush. Make sure there aren’t any pieces of dried paint latched onto the bristles, as these could scratch, scuff or otherwise damage the shaver’s mechanisms. [7]
  3. Watermark wikiHow to Clean an Electric Shaver
    Some electric shavers are specifically constructed to be cleaned with water without damaging the mechanism. For these, you can hold them under the tap and wash with hot water. You can also use soap if you need to clean any gunk or grime out of your shaver.
    • Not all shavers can be cleaned with water and some might be irreparably damaged. Make sure to check the owner’s manual before trying to clean your shaver with water. [8]
  4. Wipe down the shaver’s body and parts with a towel, then allow it all to air dry. The last thing you want is to put everything back together with drops of water trapped inside. [9]
  5. Watermark wikiHow to Clean an Electric Shaver
    These are usually sold by your shaver’s manufacturer. [10] They will lubricate and de-grease the shaver’s blades and other mechanisms. [11] Instructions may vary depending on the cleaner, but usually you should just need to spray a bit of the cleaner into the shaver after removing the shaver head.
  6. Watermark wikiHow to Clean an Electric Shaver
    The complexity of this step will depend on how thoroughly you had to disassemble the shaver. Reverse the order of your disassembly, until your shaver is put back together. [12]
  7. Advertisement
Part 3
Part 3 of 3:

Maintaining your Shaver

PDF download Download Article
  1. Watermark wikiHow to Clean an Electric Shaver
    After removing the shaver head, tap the body with your finger to shake out loose hairs. [13] Because this is very simple and only takes a few seconds, you should do it after every shave, even if you’re not thoroughly cleaning your shaver. [14]
  2. Daily maintenance doesn’t need to go beyond shaking out loose hairs. However, cleaning the shaver more thoroughly will involve brushing hair out of the motor and and cutting assembly. Leaving these hairs will cause more wear on your shaver.
  3. This ensures that your shaver will keep working optimally in the long run. [15] Get replacement parts directly from your shaver’s manufacturer. It might seem expensive, but it’s a lot less expensive than having to buy a new shaver because yours was ruined by cheap parts.
  4. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What lubricant can be used on an electric razor head?
    Community Answer
    You can just use the little brush that comes with your electric razor to clean all the hair out.
  • Question
    How do you clean and sanitize a Braun electric shaver series 6 with cleaning solution provided with the shaver?
    Ariful Haque
    Community Answer
    Choosing the right lubricant for an electric razor head is essential to ensure smooth operation, prevent irritation, and extend the life of the razor. Here are some suitable options. Many manufacturers offer specialized lubricants designed specifically for electric razors. These lubricants are formulated to provide the right consistency without harming the razor's components. Check your razor's user manual or contact the manufacturer to see if they recommend a particular lubricant. Alternatively, a few drops of a light machine oil, such as sewing machine oil or clipper oil, can be applied to the razor head.
Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      About This Article

      Thanks to all authors for creating a page that has been read 61,033 times.

      Did this article help you?

      Advertisement