Download Article
Download Article
Are your blinds too wide to fit your window? You don't have to go curtain shopping just yet. It's actually fairly easy to cut blinds down to size, whether you're working with Venetian blinds, vinyl mini blinds, or something else. Check out the steps below to learn how to cut the head rail and slats on your blinds so they fit perfectly in your window.
Steps
-
Measure the width of the window to determine the necessary width of the blinds. Typically, a set of inside-mount blinds should measure about 1 ⁄ 2 inch (1.3 cm) less than the width of the window frame. Make sure you measure the inside of the frame, where the blinds actually fit, and not the entire window frame.- Measure in at least three places -- the top, bottom, and middle of the window.
-
Mark the smallest measurement, and cut to this. Most windows are going to have regular, even spacing, but older houses may have some variability. If there is a change, use the smallest measurement taken.Advertisement -
Subtract 1/4-inch from each side to ensure the blinds have room to move up and down. This small gap will keep your blinds from getting cut or stuck on the windowsill. -
Measure the blinds from the head rail and use a pencil to mark your new desired length. Use the measurement found above and mark the headrail (the top of the blinds) at this length. You may either cut an even amount off of both sides or cut only from the pull cord side.- If the chords are on one side, you can cut only from the other side. In many ways, only cutting one side is much easier.
-
Cut the blind headrail using a hacksaw or tin snips. Simply start sawing to remove the headrail where you noted:- Remove the metal end stiffener bracket from the side(s) you are cutting.
- Use the hacksaw or tin snips to cut the headrail per your measured mark.
- File any rough edges with a metal file. However, keep in mind that the headrail edges will be covered by the mounting brackets, so a rough cut will not be visible.
- Replace the metal end stiffener onto the newly cut headrail. [1] X Research source
Advertisement
-
Line up the blind slats and the bottom rail evenly. Ensure that the pull cord is fully engaged so there is no slack. -
Secure the ends of the slats with rubber bands or a clamp. Make sure they are tight, but also even. You want them to line up perfectly for a perfect cut.- The band or clamp should be on the inside of wherever you're making your cut.
-
Cover the ends of the slats with masking tape to prevent chipping or splintering. This is especially helpful if you are working with wood or faux wood blinds. -
Measure and mark the appropriate width. This will be right in line with your newly cut headrail. Use a straight edge to ensure they are lined up nicely and draw a line to cut with. -
Ensure that the headrail is not in the way of the saw blade by sliding all of the slats over to one side. Once you've created your line, slide the slats away from the headrail, if possible. -
Cut the blind slats and bottom rail using a circular saw or table saw. For plastic blinds, you might even be able to use a powerful set of sheers. -
Confirm that all slats, the headrail, and the bottom rail are cut at the same length. If not, trim individual elements as needed to ensure a consistent width. Use some sandpaper to clean off the edges of the blinds.
Advertisement
Video
Community Q&A
Search
-
QuestionHow do I cut to the length of woven and wood window coverings?Community AnswerTake them to a home store and have them cut professionally. Don't try to do it yourself -- you'll end up being dissatisfied.
-
QuestionHow do I cut a notch in my blinds to make room for a door latch?Community AnswerIf you only need to trim a few of the slats shorter and the blind is mounted permanently onto a door, then I would say to use tin snips or sheers.
-
QuestionCan I cut tape blinds that are 131 cm. wide to 110 cm.?Community AnswerYes you can, but make sure it's not slanted or else you'll end up with some weird blinds.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
-
Thanks
- If you are uncomfortable cutting your blinds at home, most retail locations or large hardware stores will do the work for a nominal fee.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Things You'll Need
- Blinds
- Tape measure
- Hacksaw
- Tin snips
- Pencil
- Metal file
- Masking tape
- Clamp
- Power saw
References
About This Article
Article Summary
X
To cut blinds, start by marking a straight line on the head rail where you want to cut it using a pencil. Then, use a hacksaw or tin snips to cut the head rail along the line. Once you've cut the head rail, secure the ends of the blind slats with a rubber band and cover the ends with masking tape so they don't splinter or chip. Then, line the head rail up with the slats and mark the end of the head rail on the slats so you know where to cut them. Finally, use a circular saw or table saw to cut along the mark on the slats. To learn how to calculate how much you should cut off your blinds, read on!
Did this summary help you?
Thanks to all authors for creating a page that has been read 311,999 times.
Reader Success Stories
- "I was under the impression that I couldn't alter my Venetian blinds. Your instructions have saved me a headache by confirming that it was possible, thank you." ..." more
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"I was under the impression that I couldn't alter my Venetian blinds. Your instructions have saved me a headache by confirming that it was possible, thank you."
..."
more
"Worked cutting blinds in the past. This procedure confirmed how I performed the task. Taught me about binding the end, which I didn't do originally. "
..."
more
"I'm glad that I could follow the rules of how to repair my blinds, thank you. I will surely make use of your excellent advice."
..."
more
"Help make me comfortable with cutting horizontal blinds."
"Helped with knowing what tools to use."
