How to Drill Out a Lock

Open your door quickly and easily with a few simple tools

Co-authored by Robert Vallelunga and Eric McClure

Last Updated: March 1, 2024 Fact Checked

Lock drilling is the last resort if you’re locked out of a door and you need to get in fast. While drilling the lock will destroy it, you won’t have to pay (or wait for) a locksmith and the old lock can always be replaced. Plus, it's pretty simple—drill a hole just above the keyhole to destroy the tumblers, then use a flathead screwdriver to open the door. We’ll break it down for you in detail below.

Things You Should Know

Drill into the lock just above the keyhole. The goal is the drill through all of the pins inside the lock cylinder.
Go slow, and whenever the drill bit gets stuck, switch to the next size up and keep going.
After you drill through the pins, insert a flathead screwdriver into the keyhole and twist it to unlock the door.

Section 1 of 1:

Drilling Out a Lock

Download Article

1
Confirm the lock can be drilled out by looking at it. The only locks you can drill out are the doorknob locks and deadbolts with traditional tumblers. Tubular locks, ceramic locks, smart locks, cam locks, and mortise locks can only be drilled out or disassembled by locksmiths. ^{[1]
X
Research source}
- Basically, if the keyhole isn’t set in a circular metal platform and the key isn’t a “normal” key, you must break the lock to open the door.
- It's also important to double-check and make sure that you're working with a basic tumbler lock that you'll be able to knock out.
- Trying to drill out a non-tumbler lock may destroy your door, drill bit, drill, or lock mechanism and make it even harder to get in.
- If you’re struggling to picture what kind of lock you can drill out, just imagine any interior door in a standard home. Those kinds of knob locks and deadbolts can be drilled out.
2
Acquire a drill and different sizes of drill bits. Any type of drill bit should work, but steel, black oxide, and titanium drill bits will work best. To drill through a lock, you need: ^{[2]
X
Research source}
- A power drill .
- Multiple drill bits .
- A center punch and hammer . This is optional, but it will help a lot if you have one.
- Protective eyewear (to keep shards of metal out of your eyes).
Advertisement
3
Hammer a center punch directly above the keyhole (optional). If you don’t have the steadiest hands with a drill, punch a divot just barely above the keyhole’s shear line to guide your drill. ^{[3]
X
Research source}
- The shear line is where the pins enter the lock’s opening to meet the key’s ridges, so if the lock is installed where the key’s ridges point up when you open it, put the center punch just above the top of the opening.
- Some locks are installed upside down. If the key would go into the keyhole with the ridges pointing down, set the center punch guide hole on the bottom.
If you don't have a bit that size, go with something in the neighborhood. So long as the bit is roughly as big as the widest part of the keyhole, it will work. ^{[4]
X
Research source}
5
Drive the drill bit slowly into the lock above the keyhole. Hold the drill straight and go slow. The goal here is to destroy the pins inside the lock cylinder which allows you to force the lock open. Most locks have about five tumbler pins to drill through, although some have six or more. ^{[5]
X
Research source}
- You’ll feel more resistance as the drill bit encounters each pin. That’s completely normal.
6
Go slowly and stop once your drill bit starts spinning. Don’t try to drive through the entire lock all at once. You’re just going to break the drill bit if you force it too hard. Feel the drill work and stop once it gets stuck or starts spinning in place. ^{[6]
X
Research source}
- Keep the drill level while drilling. If you drill at an angle, you can accidentally drill through unnecessary metal and your door.
7
Switch to a slightly larger bit when the small bit gets stuck. After going through with your smaller bit, take it up a notch. Attach a 1/4-inch (6.5mm) or larger drill bit to your drill, and go through the lock again with the larger bit to break up the pins more and open the lock. ^{[7]
X
Research source}
- It normally only takes 2 drill bits to get through a traditional lock, but use a third bit that’s even bigger if your second bit gets caught.
Use a little bit of force to insert the screwdriver into the key hole ( not the hole you drilled). Turn the lock in the same direction you would with a key. If the drilling worked, the lock will turn and the door will open. ^{[8]
X
Research source}
9
Continue drilling and testing the screwdriver if the door won’t open. It’s possible you didn’t drill through all of the tumblers in the lock if it won’t open. Switch to a larger 3/4 inch (19 mm) drill bit and repeat the process. Keep using larger bits and your flathead until the door opens. ^{[9]
X
Research source}
- If you still can’t get the lock to open, contact a locksmith. There may be an anti-drill plate installed behind the tumblers that you can’t see keeping you from opening the door.

Community Q&A

Search

Add New Question

Question

Will this work on a tall file cabinet too?

Glenn Letteer

Community Answer

File cabinets generally have two types of locks, pin tumber and waffer. It is not possible to drill a waffer lock as they have no shear line. The keyways on file cabinet pin tumbler locks are very small. As such, if you are going to attempt drilling one, you need a much smaller bit. If you choose the wrong bit size, you may split the cylinder plug. If this happens, you have a problem on your hands.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 12 Helpful 29
Question

Can I drill a front door tumbler that has locked me in?

Upnorth Here

Top Answerer

Yes, you can generally drill any lock cylinder that is not made of metal harder than your drill bit. If your front door is a required "means of egress" for fire safety, it should not require any keys to exit. In many places it would be a violation of fire code and building code.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 3 Helpful 9

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Do not touch the drill bit or the lock with bare fingers while drilling, as it will be extremely hot.

Thanks
Helpful 1 Not Helpful 1

Things You'll Need

Drill
Drill bits
Flathead screwdriver
Safety goggles
Hammer (optional)
Center punch (optional)

You Might Also Like

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

Log in

How to Drill Out a Lock

Things You Should Know

Steps

Drilling Out a Lock

Community Q&A

Video

Tips

Warnings

Things You'll Need

You Might Also Like

References

About This Article

Reader Success Stories

Did this article help you?

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories