Download Article
Download Article
This article will teach you a super easy way to form acrylic plastic sheets without cracking, splintering, or destroying the sheet. Note that this is not on the level of mixing and pouring a fluid for intricate forms. Instead, this is for taking an existing plastic sheet and cutting and bending it to a form. You'll need cold weather gloves, strong scissors, your mold and an oven.
Steps
Download Article
-
Measure the inside of your oven. As you'll need to put the plastic sheet into the oven, this is your size limitation. -
Have a mold ready to use. The example here is the outside of a mold, but it can work inside, too.Advertisement -
Make adjustments appropriate to the specifications of your project. The only major variable that can affect the forming process is the thickness of the plastic sheet. This article uses a sheet about 1/4" thick, so all times are about 10 to 15 minutes per step. For thicker sheets, it will take longer, and for thinner sheets, it will take less time. Modify the timing as necessary. [1] X Research source -
Measure the size of the of the overall piece you need. Make sure the sheet is just big enough for the form. Use a plastic cutting knife to cut the sheet down to the general overall size. [2] X Research source -
Mark the shape with a black felt tip pen. This should include any interior cutouts, corners, etc. -
Place the plastic sheet on a cookie sheet and place in an oven set to 250 F. Wait about 10 minutes for it to warm fully. When it's ready you'll find it flexible when you try to pick it up. [3] X Research source -
Put on your gloves when you work with the plastic. It's hot and will burn you if you're not careful. [4] X Research source -
Cut any curves, corners, cutouts, etc. using the heavy shears or scissors. You'll have about 2 minutes before it cools and hardens too much to cut. If it gets too hard, put it back in the oven to warm up again. [5] X Research source -
Place back into the oven once it's cut to form, and raise the temperature to no more than 275 F. At 300 F. it will begin to stick to the cookie sheet. Above that temperature it can melt and/or begin to bubble. [6] X Research source -
Pull the plastic out and quickly press onto or into the mold that is ready. Use your fingers and firm pressure to press into any corners, fold, bends, etc. Continue to hold and press into shape until it begins to harden. -
Quickly dunk into cold water to cool and set the piece. -
If there is a mistake, reheat and start over again. -
Final check. If there are a few curves or bends that need correcting, you can turn on a burner on low to pass the piece back and forth over to SLOWLY heat it up for localized bends.
Advertisement
Expert Q&A
Search
-
QuestionIs there another method that can be used to bend acrylic?Abraham Schwartz is a handyman and the owner of Fixin’ To Do, a home improvement service in Austin, Texas. Abraham specializes in both small to medium residential and commercial sized jobs, ranging from TV mounting to furniture assembly to home automation setup. Prior to starting Fixin’ To Do, Abraham worked for over 10 years as a handyman for third party services and had a lifetime of learning how to improve houses. He holds both his TSBPE Plumbing Examiners and Electrical Apprentice (TX) Licenses. In 2018 and 2019, Fixin’ To do was rated as a Top Pro by Thumbtack.It depends on the thickness of the acrylic and the key is to warm it up slowly. If you do it in any cold environment, it is more likely to crack. It's a matter of trial and error and being patient with it. Start with a blow dryer at a medium setting to soften it and then once it gets soft enough to where it's pliable, gently bend it.
-
QuestionAre there any health/safety precautions to be taken? Is it safe to just put the plastic in the oven?Community AnswerIn most cases yes, but if you're using a kind of plastic that either has a very low combustion temperature, or gives off nasty fumes when heated, then I would suggest using an air mask to protect yourself. Look online to see whether this sort of thing would happen with your specific type of plastic. This will not happen for acrylic sheets, as they are safe to mold.
-
QuestionIf my mold is made of plastic, will it melt or get stuck in the plastic that I'm molding?Yonaton ChanowitzCommunity AnswerDepending on what type of plastic it is, it probably will stick to it. You can put parchment paper sheets between the mold to avoid this, but the heat from the thermoplastic may warp the mold.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- If the area to bend is on an outer curve or bend, or if you want to create a tighter corner, try using a frying pan on LOW heat to hold the plastic area to bend. Once heated it will bend easily.Thanks
- The reason this works is because acrylic plastic actually melts at 405 F. Try to actually melt plastic waste pieces to see if they will join and pour or flow into tighter molds.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Don't heat to more than 300 F. or you will begin to create bubbles in the plastic.Thanks
- Make sure you use heat (cold) resistant gloves. They will still get hot as you work.Thanks
Advertisement
References
- ↑ http://www.earthguild.com/products/riff/rpolymer.htm
- ↑ https://www.naturalhandyman.com/iip/infxtra/infacrylic.html
- ↑ https://ourpastimes.com/mold-plexiglass-6105219.html
- ↑ https://ourpastimes.com/mold-plexiglass-6105219.html
- ↑ https://www.youtube.com/watch?v=s23lMNN1lyE
- ↑ http://www.earthguild.com/products/riff/rpolymer.htm
About This Article
Thanks to all authors for creating a page that has been read 250,667 times.
Reader Success Stories
- "I think this is a great idea. My husband is going to make acrylic shapes as a guide to run my daughter's sewing machine along the side for quilting straight lines or wavy patterns. To buy these from a sewing store they cost an average of $30 apiece for one shape." ..." more
Advertisement
91%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"I think this is a great idea. My husband is going to make acrylic shapes as a guide to run my daughter's sewing machine along the side for quilting straight lines or wavy patterns. To buy these from a sewing store they cost an average of $30 apiece for one shape."
..."
more
"I have been trying to form Windows for my 1941 airplane, and found this very helpful. To have them done the shop needed a 9' x 9' oven, and it costs $100. So for little projects, this has been golden. "
..."
more
"The level of detail in this article was better than the instructions I found on this topic. I'm ready to make a sword out of an acrylic pipe now!"
..."
more
"It gave me a good starting point, as well as the steps to follow as I go through the process. Thank you!"
"It gave me all the information I needed to know. Very helpful and easy to understand."
