How to Fix a White Out Tape Dispenser

Co-authored by wikiHow Staff

Last Updated: August 7, 2024 Fact Checked

White out tape is a fast and easy way to redact information or correct an error in a written document. But sometimes the tape can become unwound and loose. Luckily, it’s really easy to fix white out tape. Start by taking apart the dispenser so you can access the wheel of tape. Then, tighten up the spool to remove the slack. Put the dispenser back together and you’re good to go!

Part 1

Part 1 of 2:

Opening the Dispenser

Download Article

1
Place the dispenser face-up in front of you. Set the plastic white out tape dispenser on a flat surface like a table or a desk. Keep it face-up so the logo is facing you and the tape side is facing down. ^{[1]
X
Research source}
- Work on a clean surface so the tape doesn’t stick to anything.
2
Wedge a flathead screwdriver in between the crack where the 2 halves connect. The dispenser consists of 2 connected halves and you can see the line where they connect running through the center of the narrow side. Take a screwdriver and gently insert it into the crack. ^{[2]
X
Research source}
- Don’t force the crack apart or you could break it.
Tip: Use a butter knife or even a coin to help separate the 2 halves if you don’t have a screwdriver that fits.

Advertisement
3
Apply gentle pressure to separate the 2 halves of the dispenser. Once you’ve got the screwdriver wedged into the crack, start to apply gentle, downward pressure. Continue to slowly build up the pressure until you hear a “snap” that indicates that they’re separating. ^{[3]
X
Research source}
- Be careful not to chip or crack the edges where the 2 halves connect with the screwdriver.
4
Use your fingers to pull the 2 halves apart. When you hear and feel the halves of the dispenser snap apart, remove the screwdriver and apply pressure with the tips of your fingers to finish separating them. You’ll see the wheel of the white out tape attached to 1 half of the dispenser. ^{[4]
X
Research source}
- Don’t snap or bend the dispenser to open it or you could break it.

Part 2

Part 2 of 2:

Tightening the Slack

Download Article

Once you’ve opened the plastic case, lay the half that contains the tape wheel down so it’s easier to work on. Keep the tape dispenser side facing up towards you. ^{[5]
X
Research source}

Tip: Keep the other half of the dispenser nearby so you don’t lose it.
2
Use your fingertip to immobilize the bottom of the larger wheel. Hold the half of the dispenser with the tape wheel still with one hand. Insert the index finger of your other hand between the spools to hold the larger wheel in place. ^{[6]
X
Research source}
- Holding the wheel in place will help you rewind the spool of tape.
- You don’t need to apply much pressure to keep the wheel still.
3
Rotate the wheel clockwise to start tightening the tape. While you’re keeping the larger wheel immobile, release enough pressure to allow you to rotate the wheel clockwise. The white out tape will start to re-spool on the wheel and the slack will tighten up. ^{[7]
X
Research source}
- Continue to turn the wheel until all of the slack is gone, but don’t tighten it so much that it snaps the tape.
4
Reconnect the 2 halves of the plastic cover of the dispenser. After you’ve taken the slack out of the white out tape and the spool is re-wound, take the other half of the dispenser and line up the edges of the 2 halves. Apply pressure with your hands until you hear them snap back together. ^{[8]
X
Research source}
- You shouldn’t have to apply too much force to reconnect the two halves.
- Be careful not to break the edges that line up on the halves of the dispenser.
5
Apply a small strip of white out on a piece of paper to test it. With the slack removed and the dispenser put back together, apply a small strip of the white out tape to a piece of paper. Use it as you normally would so you can test it to make sure it’s working properly. ^{[9]
X
Research source}
- If the white out tape continues to function improperly or come unwound, you may need to replace the white out tape dispenser.