How Does a Toilet Work? A Step-by-Step Breakdown

PDF download Download Article
Learn the science behind what happens when you flush your toilet
PDF download Download Article

You use your toilet every day, but have you ever stopped and wondered how it actually works? Toilets are pretty simple plumbing fixtures that only use a few mechanical pieces to function. Knowing how your toilet works makes it a lot easier to troubleshoot and fix any issues that occur, and we’ll walk you through each step. Keep reading to learn how water flows through your toilet from the tank, into the bowl, and down your pipes.

Things You Should Know

  • When you flush your toilet, the handle lifts the flapper at the bottom of the tank. Water flows through the valve into the toilet bowl through the rim holes.
  • Water rushes through the siphon jet at the bottom of the bowl and forces water and waste through the S-shaped trap.
  • The flapper closes and makes a watertight seal on the tank. The fill valve adds water to the tank up to the max fill line so your toilet is ready to use again.
1

The toilet handle opens the tank’s flapper.

PDF download Download Article
  1. When you press down on the handle to flush the toilet, it lifts a lever inside the tank connected to a chain and circular rubber flapper . As the flapper lifts up, it breaks the watertight seal at the bottom of the tank so the water can start flowing into the bowl. The flapper floats in the water to stay open even after you let go of the handle. [1]
    • If the flapper doesn’t open, try adjusting the chain length so it’s shorter.
    • Sometimes, the plastic parts on the inside of the handle can break. If the handle feels loose or doesn’t open the flapper, then replace the assembly .
    2. Advertisement
2

Water flows from the tank into the bowl.

PDF download Download Article
  1. Most toilets tanks release about 2 gallons (7.6 L) of water every time you flush. The water travels through the flush ring , a channel just underneath the toilet seat, to enter the bowl. [2] About 20% of the water goes through small rim holes along the edge of the bowl to rinse away any waste. The remaining water gets directed into a channel along the bottom of the bowl called the siphon jet to help your toilet start flushing. [3]
    • If there’s no water in your tank, make sure you turn on the water supply using the valve on the wall behind your toilet.
3

Water siphons from the bowl down the drain pipe.

PDF download Download Article
  1. Normally, the water level sits just below the highest point of the S-trap , which is the curved section at the bottom of your toilet that leads to the drain pipe. After you flush and the level rises, the water rushes over the top of the S-trap and creates a siphon. This siphon acts like a vacuum that pulls all the water and waste out of the bowl and through the S-trap. Once the water level is low enough for air to get back into the S-trap, the siphon stops and the bowl starts filling up again. [4]
    • If your toilet doesn’t flush, it could be a sign of a clog. Try unclogging your toilet with a plunger or plumbing snake.
    • If there isn’t enough water to start the siphon, then there may be an issue inside the tank. Adjust the fill valve or float to raise the water level and improve the flush power.
    2. Advertisement
4

The flapper closes and seals the tank.

PDF download Download Article
  1. As water empties out of the tank, the flapper will slowly drop back down to cover the flush valve. The flapper creates an airtight seal so the tank can refill without leaking into the bowl. [5]
    • If the flapper doesn’t close completely or there’s water leaking into the tank, make sure there are no obstructions between the flapper and valve. Fix a flapper by adjusting the length of the chain or by replacing the unit completely.
5

The fill valve refills the tank.

PDF download Download Article
  1. The fill valve is usually a tall plastic piece near the back of your toilet tank that pulls water in from the supply line. The water flows from the valve and into the tank to raise a float , which either looks like a balloon or a plastic cylinder on the flush valve. When the water level reaches the max fill line on the vertical overflow tube and raises the float, the fill valve shuts off so your toilet doesn’t keep running. [6]
    • The overflow tube leads directly to your toilet bowl so the tank doesn’t overflow if the water level rises higher.
    • It’s normal for water to go through a small hose from the fill valve to the overflow tube while the tank is refilling. Once the fill valve shuts off, the water will stop going into the overflow tube as well.
    • If you’re fixing a running toilet , check to make sure the flapper is completely closed and undamaged. If that doesn’t work, then adjust the height of the float or replace the fill valve .
    2. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      • Most toilet issues are easy DIY jobs, but don’t hesitate to contact your local plumber if you’re having trouble diagnosing or fixing the issue.
        Thanks
        Helpful 0 Not Helpful 0
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • Try to fix any leaking pieces in your toilet right away since they could potentially increase your water bill. [7]
        Thanks
        Helpful 0 Not Helpful 1
      Advertisement

      You Might Also Like

      How to
      Adjust Soft Close Toilet Seat Hinges
      How to
      Use a Toilet Seat Cover
      How to
      Replace a Toilet Seat
      What to Do if Your Toilet Fill Valve is Leaking
      How to
      Measure a Toilet Seat
      How to
      Retrieve an Item That Was Flushed Down a Toilet
      How to
      Fix a Leaky Toilet Supply Line (Water Supply Line Replacement)
      DIY Toilet Installation: A Complete How-To Guide
      How to
      Caulk Around a Toilet Base
      The Best Ways to Keep Toilets Clean and Stain-Free Without Scrubbing
      How to
      Clean a Toilet Brush & Holder
      How to
      Install a Raised Toilet Seat
      How to
      Install a Toto Washlet
      7 Reasons Your Toilet Tank Isn’t Filling with Water (& How to Fix It)
      Advertisement

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about toilets, check out our in-depth interview with Dave Jones .

      References

      1. ↑ https://youtu.be/UDa0VTwBd1U?t=49
      2. ↑ https://youtu.be/LmsIYwf8QqQ?t=144
      3. ↑ https://youtu.be/q9RMoKmbamM?t=141
      4. ↑ https://todayshomeowner.com/plumbing/guides/how-does-a-toilet-siphon-work/
      5. ↑ https://www.bobvila.com/articles/toilet-repairs/
      6. ↑ https://youtu.be/UDa0VTwBd1U?t=67
      7. ↑ https://ci.stcloud.mn.us/DocumentCenter/View/19181/Common_Causes_of_High_Water_Bills

      About This Article

      Thanks to all authors for creating a page that has been read 10,887 times.

      Did this article help you?

      Advertisement