Download Article
Download Article
This article explains how a beginner can make glass beads from scratch, using a method called "lampworking".
Steps
Download Article
-
Set up your area. Good work always starts with having a good workspace.- Clean up an area to work on.
- Pick up any objects that you wouldn't like to be damaged.
- Clamp the torch head and gas canister to the table (follow instructions provided by the manufacturer).
- Clean up an area to work on.
-
Arrange the rest of the equipment for easy access. Make sure you can get to everything without reaching across the torch (even when off it will retain heat).Advertisement -
Before you make a bead , prepare the mandrels. Take each one and rub firmly with wire wool. This cleans the metal and helps the bead release adhere to the surface. -
If a powdered bead release is to be used, mix it according to the manufacturer's instructions. Dip each mandrel in the bead release and leave to dry. Some bead releases can be dried in the flame; however, if yours does not say to do this, then leave to air dry, as it may crack otherwise. -
When dry, check each mandrel to make sure that the coating is even and intact. Discard any mandrels with cracked bead release because if the glass comes in contact with the mandrel, it will stick and will likely be impossible to remove. -
-
Adjust the flame until you have a sharp edged blue cone. A bushy flame means you have too much gas. -
Select the color of glass you want to start with. Take it into your dominant hand and, holding it horizontally, slowly wave it in and out of the flame just above the tip of the blue cone. If you heat the glass too quickly then it may "shock" or shatter. -
When the tip begins to glow, leave the glass in the flame a little longer, then start rotating the rod as a ball starts to form at the tip. [1] X Research source -
When ready to start forming your bead , take the mandrel with your other hand. Try to keep the glass in the flame and keep rotating and so that it doesn't droop or cool, warm the mandrel in the flame just behind the glass. Hold the mandrel horizontally. [2] X Research source -
Carefully alter the position of the rod in your hand so that you are holding it like a pencil. [3] X Research source -
Gently press the ball of molten glass through the flame and onto the mandrel. At the same time, start rolling the mandrel slowly away from yourself. [4] X Research source -
Stay in the flame. The rest of the glass rod will slowly soften as you roll more onto the mandrel. -
When you have added enough glass, pull away the glass rod (remember to keep the mandrel rotating in the flame). You will get a thin string of glass, just allow the flame to melt through it. [5] X Research source- Place your glass rod onto the rod rest, out of the way.
- You may want to switch your mandrel into your dominant hand at this point. To do this, carefully bring the mandrel in front of the torch. Never try reach over the flame.
- Place your glass rod onto the rod rest, out of the way.
-
To round up your bead, keep the mandrel rotating in the flame until a smooth form is achieved. [6] X Research source- Add any decoration or other colours.
-
When finished, slowly remove the bead from the flame (remember to keep rotating) when the glow fades. Put the bead and mandrel in between two sheets of fiber blanket, or into a pot of vermiculite to cool. Be careful not to disturb the bead – if it cools too fast it may crack.- To check if your bead is cool enough to go into the fiber blanket or vermiculite without damaging it, hold the bead under your work area (don't forget to rotate) and see if it is still glowing – as soon as the glow fades, put it into the fiber blanket or vermiculite.
-
When cool, soak the bead and mandrel in water to remove the bead release. If you have trouble removing the bead, grip the mandrel with a pair of vise pliers and try to twist and pull the bead off. -
Leave the bead to soak in water. Then scrub the inside with a bead reamer or a pipe cleaner. Now your bead is ready to use.- If wished, surface treatments such as etching can also be used at this point.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- Try to keep your bead under 1/2 inch (1.3 cm) unless you have a kiln to anneal the beads in. Annealing is the process of adding strength by heating and cooling in a kiln. Without this process, glass beads risk cracking and breaking easily. [7] X Research sourceThanks
- If your match is blown out when trying to light your torch, then turn the gas lower. If the torch lights but then sputters out, then turn it up higher.Thanks
- If using propane gas keep your bead high in the flame to avoid murky dull colours. Brazing fuel burns cleaner than propane and avoids this problem.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Keep long hair tied back.Thanks
- Wear long sleeves and natural fibers, synthetics may stick to your skin if there is an accident.Thanks
- Always wear protective goggles with UV protection. Sunglasses work in a pinch.Thanks
- Dust from bead release can be hazardous – keep the bead release wet, or wear a dust mask.Thanks
- Remove dangling jewelry.Thanks
- Set up in a well ventilated area.Thanks
- Before attempting, do some research on ventilation, and annealing. Do not attempt to sell un-annealed beads, as they can spontaneously break, even years after they are made. [8] X Research sourceThanks
Advertisement
Things You'll Need
- A workbench
- 1 lb canister of brazing fuel (MAPP gas) or propane
- Matches
- Single fuel torch head (hothead)
- Mandrels (metal doweling)
- Wire wool
- Bead release or kiln wash
- Fiber blanket or vermiculite
- Glass rods
- A rest for your rods to cool on after use
- Metal container for water
- Bead reamer or pipe cleaners
- fire extinguisher
- (optional) Bead kiln
- (optional) Frit, millefiore, mica, stringers, etching solution etc for decoration
- (optional) Heat-proof tools for shaping (anything metal or graphite can be experimented with)
- (optional) Heat-proof board (if your workbench is not heat-proof)
- (optional) Vise-grip pliers
- (optional) Ointment for minor burns
References
- ↑ https://www.youtube.com/watch?v=nmKmxZCJKGg
- ↑ https://www.youtube.com/watch?v=k1gn-YorlCs
- ↑ https://www.youtube.com/watch?v=k1gn-YorlCs
- ↑ https://www.youtube.com/watch?v=k1gn-YorlCs
- ↑ https://www.youtube.com/watch?v=k1gn-YorlCs
- ↑ https://www.youtube.com/watch?v=gN6V_P6pLAY
- ↑ Jean Power, 200 Beading tips, techniques & trade secrets, p. 10, (2009), ISBN 978-0-312-58747-5
- ↑ Jean Power, 200 Beading tips, techniques & trade secrets, p. 10, (2009), ISBN 978-0-312-58747-5
About This Article
Thanks to all authors for creating a page that has been read 149,122 times.
Advertisement
84%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
