PDF download Download Article PDF download Download Article

Using a HDTV (High-Definition Television) antenna, based on the DB4 design, is 1 of the most effective ways to retrieve HDTV signals. Purchasing this type of antenna at a store will cost you at least $40. However, you can build such an antenna yourself at a much lower cost. The following is a guide on how to make a HDTV antenna.

Things You Should Know

  • Get a wooden board that is 1x3x22 inches. Beginning at 2 inches in, draw lines that are 5.25 inches apart across the board with two evenly spaced dots on each line.
  • Cut 8 14 inch pieces of copper wire and fold them into "V"s. Use screws and washers to attach the creased side of the wire to each of the dots.
  • Connect a balun to the two center sections of wire and connect to an HDTV using a coax cable.
    • It should be 1x3 inches (2.54x7.62 cm) or 2x3 inches (5.08x7.62 cm).
    • It should be 22 inches (55.88 cm) long.
    • Going from left to right with the board laying horizontally, mark lines at the 2 inch (5.08 cm) mark, the 7.25 inch (18.42 cm) mark, the 12.5 inch (31.75 cm) mark, and the 17.75 inch (45.09 cm) mark. Use a marker or a pencil.
    • Mark 2 dots on each line that are evenly spaced.
    • Each section should be 14 inches (35.56 cm) long.
    Advertisement
    • Each should be bent so that each side is 7 inches (17.78 cm) long.
    • The gap between each side should be 3 inches (7.62 cm) long.
    • Each wire should resemble a "V" when you are finished.
    • Attach the center (bent portion) of each wire to the dotted areas of the board using screws and washers.
    • When finished, each v-shaped wire should extend outward from the board.
    • Use the remaining portion of the wire for this.
    • The bent portion of the v-shaped wires should be intersected once each.
    • The wires should not touch each other.
    • Be sure that at least 1 of the wires that you weave is insulated. Vinyl insulation will work well.
    • When finished, the wires should resemble 2 "X" shapes that connect the first and second and the third and fourth sets of v-shaped wires, respectively. Two horizontal lines should connect the "X" designs between the second and third sets of v-shaped wires.
    • Two reflectors should be evenly spaced on the back of the board.
    • Each reflector should be 15x9 inches (38.1x22.86 cm).
    • Use screws to complete this task.
    • The reflectors should not touch the v-shaped wires.
    • This is a transformer that can be purchased on the Internet or at an electronics retailer.
    • Follow the instructions that come with the balun.
    • Use a coax cable, which can be purchased on the Internet or at an electronics retailer.
    • Follow the instructions that come with the coax cable.
  1. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What are grill screens?
    Community Answer
    Aluminum window screen material, hardware cloth, or any type of metal screening that is no more than 1/2" squares. Cut to the proper size, most metal will become a suitable reflector, as long as any holes are under that dimension. This is frequency related and will vary by the signal you're trying to capture.
  • Question
    Can copper insulated wire be used?
    Community Answer
    Yes. The velocity factor may be different, but probably close enough to bare wire.
  • Question
    What gauge wire should be used? Distance from edge for holes? Also, the dimensions shown in the first step don't make any sense, they add up to 58.75 inches. At best, the drawing is poorly done.
    Robinson Valderrama
    Community Answer
    The drawing and measurements are poorly made, the distance between each point is 5.25 inches, this gives a total of 15.75 inches.
See more answers
Ask a Question
      Advertisement

      Tips

      • Wire coat hangers may be substituted for copper wires. Be sure to mimic the mentioned setup of the wiring and strip any paint or varnish off of the coat hangers where they touch the wire.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Things You'll Need

      • Wooden board that is 22 inches (55.88 cm) long with a specification of 1x3 inches (2.54x7.62 cm) or 2x3 inches (5.08x7.62 cm)
      • Marker or pencil
      • Screws
      • Washers
      • Fifteen feet (4.57 m) of copper wire or wire coat hangers
      • Two 15x9 inch (38.1x22.86 cm) grill screens
      • Balun
      • Coax cable
      • Wire cutter
      • Screwdriver

      About This Article

      Thanks to all authors for creating a page that has been read 333,302 times.

      Reader Success Stories

      • Bear A.

        Nov 3

        "I made one it works great."
        Rated this article:
      Share your story

      Is this article up to date?

      Advertisement