PDF download Download Article PDF download Download Article

Do you have an old papasan or "satellite dish" chair with a ratty (or entirely missing!) cushion? There's no need to buy a new one! You can replace it by making a new one out of a few old bed pillows and some heavy cloth. See Step 1 to get started.

  1. 1
    Acquire a papasan chair frame if you don't already have one.
  2. 2
    Dig all those old pillows out of your closet or garage and launder them. Remove the pillow slips and pillow covers. Cut the pillows diagonally to form wedges.
    Advertisement
  3. 3
    Place 6-8 of your half-pillow wedges on the chair seat, arranging them until all of the rattan frame is thickly covered. This could take anywhere from 6 to 10 pillow wedges (3-5 old pillows) depending on their thickness and the number of times they've been washed previously.
  4. 4
    Lay the wedges on two large pieces of cloth for the cover. (You should cut both sides at the same time, as they'll be sewn together later to make the cover.) Be certain your area is flat. The floor works well. Trim the edges of the wedges to make the outer edge smooth and round.
  5. 5
    Cut the two layers of material around the pillow wedges, leaving approximately a two-inch margin.
  6. 6
    Fold the resulting circles in half, and then in half again and once again to get one eighth of a circle. Trim the edges again to ensure that you have as close to a perfect circle as possible.
  7. 7
    Sew the perimeters of the two cloth circles together, leaving two feet of opening for stuffing.
  8. 8
    Turn and stuff by placing your pillow wedges snugly inside.
  9. 9
    Sew through the entire thickness and tie off snugly approximately every 12 inches (30.5 cm). Do this between each pillow wedge for easier poke through and tie off. [1]
  10. 10
    Hand baste the opening closed with raw edges to the inside of the pillow . Machine stitch the opening closed and voilà! A "new" cushion for your papasan that cost you little or nothing in "out of pocket" expense!
  11. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What material is the best to use?
    Community Answer
    Any upholstery fabric or utility fabric such as canvas or duck cloth will work. Standard fabrics are not designed for heavy use. It is possible to use regular fabrics if you apply heavy weight interfacing to the back, but it will not last as long as utility/upholstery fabrics.
Ask a Question
      Advertisement

      Tips

      • You may or may not choose to use buttons on each side of the cushion as you tie off, but using buttons helps prevent the cover from tearing.
      • You can make a slipcover out of heavy cloth for easy cleaning.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • These covers attract dust very quickly, so take caution if you have allergies.
      • Do not use feather-stuffed pillows. When you cut these open, instead of getting a lump of cushion material you can cut diagonally, you get a large cloud of downy feathers!
      Advertisement

      Things You'll Need

      • Papasan chair frame and base
      • 3-5 old pillows
      • Approximately 4 yards / 3.6 meters of 60" / 1.5 meters wide new or used sturdy sheeting material.
      • Sewing machine
      • Scissors
      • Thread
      • Embroidery floss or other heavy thread
      • Largish flat buttons
      • Optional - zipper or Velcro fastener and heavy twill for a cushion cover.

      About This Article

      Thanks to all authors for creating a page that has been read 391,583 times.

      Reader Success Stories

      • Lew Moore

        Feb 13, 2019

        "I was just called to put a covering on a papasan chair. With the great directions and pictures that were given, I ..." more
      Share your story

      Did this article help you?

      Advertisement