Download Article
Download Article
A butt weld is the easiest and most simple joint to weld, and also very common. This is a great joint to use when practicing welding as a beginner.
Steps
-
Obtain all necessary equipment. This should be a welding machine, electrode and workpiece clamps (and their leads), a welding helmet darker than shade 10, welding gloves, and appropriate safety clothing.
-
Prepare the metal to be welded. This includes grinding down rough edges and cleaning the areas to be welded.Advertisement
-
Bevel the edge of the metal if it is thicker than 1 ⁄ 4 inch (0.6 cm). Beveling allows for better penetration of the root pass and subsequent passes. Beveling can be done with an oxy-fuel torch or a plasma arc cutter, but isn't necessary on thinner metal.
-
Align your metal to make sure the edges line up well. They should be smooth and align cleanly.
-
Turn your pieces over. This should be the flat side if on or more pieces are beveled, or the side you don't want to start welding.
-
Separate the pieces a little bit and set the amperage on your machine about 10 percent higher than the level you intend to use welding the metal. So, if you are going to use 100 amps to make your weld(s), set your amperage at 110 amps.
-
Make tack welds. These will hold the metal together and prevent it from warping or bending inward when the weld is finished. To make a tack weld, strike an arc and let it sit for a few seconds. A few tack welds are usually needed and you should be able to break them with a hammer or wrench.
-
Flip your metal over to be welded.
-
Strike an arc and create your root pass. This is going to be the first and deepest pass on your weld, and if the metal is thick enough, the only pass you'll need. If you beveled the steel start at the bottom for your root pass. You need to ensure the root pass penetrates deeply enough, and for this reason 6010 electrodes are frequently used for this purpose.
- The arc length is the distance between the electrode's tip and the workpiece. You should maintain a consistent arc length throughout the process.
- Different welding processes and electrode types may have specific recommendations for the ideal arc length. Refer to the manufacturer's guidelines or welding procedure specifications (WPS) for the specific welding process you're using.
- Adjust based on electrode type. In general, it is preferable to have a shorter arc length. However, certain electrodes may require a slightly longer arc length for optimal performance.
-
Clean the weld with a hammer and wire brush and make subsequent passes if needed. These passes should strengthen the weld and fill it in. Make sure to clean each pass before you start a new one.
Advertisement
Community Q&A
Search
-
QuestionWhat is a root pass?Community AnswerA root pass is the first pass, before the cap in a two pass weld, or before the hot pass, fill pass and cap on a multi pass weld.
-
QuestionWhy is cast iron ferrous metal?Community AnswerFerrous means the alloy contains iron. As the name would suggest, cast iron contains iron, and is therefore ferrous.
-
QuestionWhat is arc welding?Mzm555Top AnswererAs detailed in this article and referred to in general life, when people refer to "arc welding", they are most likely talking about "stick welding", also called "Shielded Metal Arc Welding" (SMAW). However technically speaking, the term "arc welding" actually covers a range of welding processes that use an electrical "arc" to melt and fuse metals together. Therefore welding processes such as MIG, TIG, FCAW, SAW, and more, are considered different forms of arc welding.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- This article applies mainly to Shielded Metal Arc Welding (stick) but similar techniques can also be used in Gas Metal Arc Welding (metal inert gas or MIG).Thanks
- Allow the metal to cool in the air, as dipping it in water can make the joint brittle and allow it break more easily.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Make sure your welding helmet's lens is the proper shade for the amperage and process you're using.Thanks
- If using a torch to bevel the metal, use caution and avoid setting a brass torch tip on a hard surface.Thanks
- Always wear pants without cuffs, shirts without pockets, and safety glasses when chipping slag off welds.Thanks
- Plasma cutters use an electric arc, so safety precautions from arc welding apply to this also.Thanks
Advertisement
Things You'll Need
- Welding helmet shade 10 or higher
- Electrodes, usually 6010 and/or 6013
- Leather gauntlet gloves
- Welding machine with proper clamps and leads
- Metal to weld on
- Plasma arc cutter or oxy-fuel torch (optional)
Expert Interview
Thanks for reading our article! If you’d like to learn more about welding, check out our in-depth interview with Jones Welding & Industrial Supply Company .
About This Article
Thanks to all authors for creating a page that has been read 88,652 times.
Advertisement