How to Polish Acrylic

PDF download Download Article
PDF download Download Article

Did you know that cloudy, roughed-up acrylic can be sanded down to a shine? If you didn’t, you’re in for a treat. Polished acrylic looks crisp, shiny, and smooth. You can even flame-polish your acrylic to give it a texture resembling glass. In this article, we’ll walk you through both options so that you can choose the solution that makes sense to you. Read on to learn how to polish your acrylic.

Method 1
Method 1 of 2:

Sanding Down Your Acrylic

PDF download Download Article
  1. Place a sanding block in the corner of a sheet of sandpaper and trace an outline around the block with a pencil. Add an extra 0.5 inches (1.3 cm) to the bottom of the outline so you can place that bit of sandpaper into the sanding block. Then, take a utility knife and cut along the outline. [1]
    • You will have to repeat this process for the 320-360 and 600-grit sandpaper.
  2. Open the bottom of the sanding block to create a gap where the extra sandpaper goes and slide the paper in. The sandpaper should fit tightly on the block, meaning there shouldn't be any airspace between the paper and the sanding block.
    • The coarse side of the sandpaper should be facing away from the sanding block.
    • You can pick up a foam or rubber sanding block at your local hardware store or order one online.
    Advertisement
  3. Use lukewarm water and spray evenly, making sure to wet every part of the acrylic piece. Make sure to re-spray the acrylic as you switch sandpapers. [2]
    • Wet-sanding is what allows you to polish the acrylic and make it look shiny and new. If you forget to use water, you could damage the acrylic and make it unusable.
  4. Vigorously rub the sandpaper into the acrylic to straighten out the edges and smooth the material. This sets the table for the higher-grit sandpapers to polish up the acrylic and give it that shine you're looking for. [3]
    • To get a feel for sanding acrylic, practice on extra scraps that are left over from your project.
  5. Once you've cut out pieces of finer sandpaper and attached them to the sanding block, wet-sand the edges of the acrylic to finish the job properly. When the acrylic starts to have a greater shine to it, you know the 320-360-grit sandpaper has done its job. If you keep sanding and don't see the acrylic get shinier, that's when it's time to move on to a higher grit of sandpaper. [4]
    • Take breaks in between sanding so your hand doesn't cramp.
  6. Using a higher grit of sandpaper will make the acrylic shine even more than it already did. Sanding acrylic takes time, so don't get frustrated if the material doesn't get polished right away. [5]
    • The higher the grit of the sandpaper, the finer it is.
    7. Advertisement
Method 2
Method 2 of 2:

Flame Polishing Your Acrylic

PDF download Download Article
  1. You can pick up a torch at your local hardware or home improvement store. You can also order a torch online. Propane torches are not ridiculously expensive and have many other uses around the house. You can get a good propane torch for fewer than 50 dollars. [6]
    • Other uses for the torch include melting snow and ice on outdoor staircases and walkways, starting fires, and removing old sealant on windows.
  2. There are bound to be some extra pieces of acrylic lying around no matter what you're using the material for, so put the left-over pieces to good use by trying out the propane torch on them. This allows you to get a feel for how to handle the torch and lets you make mistakes without damaging the acrylic that's actually a part of your project. [7]
    • If you don't have any excess acrylic, go out and buy some for this specific purpose.
  3. If you move the torch too slowly, the acrylic will melt or burn and the material will be ruined. To be as safe as possible, make a pass with the torch and allow the edge to cool to the point where you can touch it with your hand. This helps you avoid burning the acrylic. [8]
    • It usually takes a couple of minutes for the acrylic to cool off after it's been torched, so wait at least that long before touching it.
  4. It should only take 2-3 passes at most to get a quality finish, and each pass should take no longer than a few seconds. When the acrylic looks like glass, that's when you know the job is done. [9]
    • Remember to allow the edges to cool before making a second and third pass over the acrylic. If you re-torch the acrylic too quickly, the material could melt or burn.
    5. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!

      Things You'll Need

      Sanding Down Your Acrylic

      • 180, 320-360, and 600-grit water-proof sandpaper
      • Extra pieces of acrylic
      • Sanding block made of rubber or foam
      • Spray bottle filled with water
      • Utility knife
      • Pencil

      Flame Polishing Your Acrylic

      • Propane torch
      • Extra pieces of acrylic

      You Might Also Like

      How to
      Cut Acrylic Sheets
      Simple DIY Ways to Polish & Restore Plastic So It Shines
      How to
      Remove Scratches from Plastic
      How to
      Fold a Plastic Bag
      How to
      Remove Plexiglass Scratches
      How to
      Remove Plastic Smell
      How to
      Glue Plastic
      How to
      Adhere Plastic to Wood
      How Do You Know If Rice Is Plastic? (Plus, Origins of the Viral Rumor)
      How to
      Dye Acrylic Plastic
      How Do You Bend Acrylic? DIY Tips & Tricks
      How to
      Make Plastic
      How to
      Build a Straw Bridge
      How to
      Easily Mold Acrylic Plastic Sheets
      Advertisement

      References

      1. ↑ http://www.bcae1.com/plexi.htm
      2. ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB
      3. ↑ http://www.bcae1.com/plexi.htm
      4. ↑ http://www.bcae1.com/plexi.htm
      5. ↑ http://www.bcae1.com/plexi.htm
      6. ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB
      7. ↑ http://www.bcae1.com/plexi.htm
      8. ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB
      9. ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB

      About This Article

      In other languages
      Thanks to all authors for creating a page that has been read 89,842 times.

      Reader Success Stories

      • Anonymous

        Oct 19, 2023

        "Explained in simple terms."
      Share your story

      Did this article help you?

      Advertisement