Download Article
Download Article
Now that you’ve set your wick, mixed and poured your wax, it’s time to remove your new candle. It’s easy to get excited when you’re so close to seeing the result of your hard work. However, be patient and efficient in removing the candle from its mold. You’ll have to remove the mold sealer and extract the candle, as well as know how to remove stuck candles.
Steps
-
Peel off putty type sealers. Putty sealers typically get molded around the base of the mold to seal the hole. They’re usually pressed into a disk and stuck to the bottom of the mold. Removing this kind of sealer is as simple as peeling it off, much like sticky tack.
-
Snap off magnetic mold sealers. Magnetic mold sealers are simple metal sheets that are magnetically charged. They snap onto the bottom of a mold to prevent wax from leaking out. Removing these is as simple as pulling them off.
- If you’re using plastic or aluminium molds, you’re likely not using a magnetic mold sealer.
Advertisement -
Pull out rubber mold plugs. Rubber mold plugs are shaped somewhat like a spinning top; they have a large base and a tapered tip. Usually they just squeeze into the hole at the bottom of a candle mold. That means removing them is as simple as grabbing the base and pulling them out.- With rubber molds, the wick may be wrapped around a wick bar at the bottom of the mold. If so, you’ll need to unwrap the wick before you can remove the candle.
Advertisement
-
Wait until the mold cools completely. If you try to remove the candle before the wax has set completely, the surface of the candle might tear and crumble. Leave the mold on a flat surface that won’t be damaged while the mold is still warm. It may take some time for the mold to cool; be patient. [1] X Research source
-
Tap on the bottom of the mold. Flip the mold upside down, so the opening faces downwards. Use your fingers to lightly tap on the bottom of the mold, which will shake the candle loose. Tap slowly and progressively, or the candle might slip out too quickly.
- Don’t bang the mold against a counter or other hard surface, since this could damage the candle. [2] X Research source
-
Tug the wick lightly. If tapping on the mold isn’t enough to dislodge the candle, you can gently tug on the couple of inches of wick poking out the top of the candle. Don’t use too much strength when pulling on the wick; you might break the string or cause it to slip out of the candle. [3] X Research source
Advertisement
-
Refrigerate the mold. Placing the mold in the refrigerator will speed up the cooling process, helping the wax set and separate from the mold. Flip the mold every 30 minutes; this will make sure the mold and wax cool evenly. Check the mold periodically; you’ll want to remove it from the fridge as soon as it’s cold to the touch.
- Make sure you wait until the mold has cooled to room temperature before placing it in the fridge. If the temperature change is too drastic, the candle could crack. [4] X Research source
-
Put the mold in the freezer for five minutes. If the candle’s especially difficult to dislodge, you can try putting the mold in the freezer. Take it out after five minutes and try to remove the candle. If it still won’t budge, leave it in the freezer for an additional five minutes. You don’t want to leave the mold in any longer than 10 minutes, since this will definitely cause the candle to crack. [5] X Research source
-
Use boiling water to remove completely stuck candles. Finally, if you’ve tried all of the above and can’t remove the candle, you might have to cut your losses. Place the mold in a metal dish filled with boiling water and wait for the candle to soften. After a few minutes, you should be able to retrieve the candle; use a pair of tongs or a wooden spoon to avoid burning yourself.
- This process won’t save your candle, but you can at least melt down the wax for use in your next attempt.
Advertisement
Community Q&A
Search
-
QuestionThere is a small metal disc stuck in bottom of the glass which had a candle in it. How do I release the disc?Community AnswerPour a small amount of eucalyptus oil into the glass jar so it just covers the disk. Leave it overnight if you can wait that long otherwise after an hour or so you can try manually lifting it using a butter knife. You can also try freezing the glass overnight which should make the wax and disc easier to remove.
-
QuestionWhy did my skull candle crack?Community AnswerYou were probably not careful enough. If you try again, handle it more gently next time.
-
QuestionI have a silicone unicorn mold, but every time I open the mold the wings break off of the candle. Do you have any suggestions for me?Community AnswerMake sure you are using a hard wax for this and not a softer wax. The softer wax tends to break with ease.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Tips from our Readers
The advice in this section is based on the lived experiences of wikiHow readers like you. If you have a helpful tip you’d like to share on wikiHow, please submit it in the field below.
- Spread oil (olive oil is best) around the inside of the mold and pour the wax in. Once wax is poured, store it in the refrigerator and keep it in there for a long time. Although wax cools really quickly, you should still chill it in the refrigerator for a long time.
- To prevent a dip in your candle, heat the container you're pouring the wax into so it acclimates. It also helps to pour your wax in slowly.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
References
- ↑ https://www.fragrancex.com/fragrance-information/a-candle-making.html
- ↑ https://www.fragrancex.com/fragrance-information/a-candle-making.html
- ↑ https://www.lonestarcandlesupply.com/candle-making/guides/how-to-make-pillar-candles/
- ↑ https://www.supplycandle.com/Metal-Candle-Molds/
- ↑ https://www.lonestarcandlesupply.com/candle-making/guides/how-to-make-pillar-candles/
About This Article
Thanks to all authors for creating a page that has been read 169,357 times.
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
