PDF download Download Article
A simple DIY guide to replacing your toilet’s flush valve
PDF download Download Article

If the flush valve on your toilet stops working properly or you have a leak, it can be time to replace the flush valve. Although plumbing work can seem like a job best left to the experts, you can replace the flush valve on your toilet with minimal hassle by following some simple steps.

Part 1
Part 1 of 3:

Removing the Tank and Old Flush Valve

PDF download Download Article
  1. Before beginning any installation, shut off the water source leading to your toilet or the toilet will flood the bathroom. [1]
    • The valve is usually located on the pipes running into your toilet from the wall.
    • Shut off the water by turning the valve clockwise until you feel resistance.
  2. Flushing the toilet will drain most of the remaining water from the toilet, allowing you to access the its internal parts more easily. [2]
    • This will also prevent any remaining water from spilling out of the toilet and all over the floor.
    • Soak up any remaining water with a sponge and bucket.
    Advertisement
  3. Next, look at the bottom of the toilet and find the one hose attached to it, the supply hose, and remove it. Then, remove the nuts and bolts from the hose with your adjustable wrench, and lift up the tank. [3]
    • Lift up the tank carefully , and it will come off the bottom portion of the toilet.
    • Turn the tank upside down, resting it on the toilet seat.
  4. Locate the thick, conical rubber gasket and remove it. Underneath the gasket you’ll see a large plastic nut. Loosen and remove the plastic nut to remove the flush valve. [4]
    • Start to loosen the nut by turning it counterclockwise with your pliers.
    • The flush valve will come right off.
    • Undo the clip (looks like a paper clip) attaching the hose by pushing it off. This clip connects the flush valve to the filler valve.
  5. Use 409 or a similar cleaning product and Clorox with bleach to clean the surfaces that touch the flush valve.
    • This will prevent any debris or residue from interfering with the flush valve's seal, ensuring that you do not get leaks.
    • Use a rag and cleaning product.
  6. Advertisement
Part 2
Part 2 of 3:

Installing the New Flush Valve

PDF download Download Article
  1. The new valve will go in the same way the old valve came out. Push the new valve through the bottom of the tank. Take the valve with the threaded side up and slowly direct it through the hole so your hand is in the tank. Be careful not to attach it too tightly, or it might cause the tank to crack. [5]
    • Make sure the black tube, extending from the top of the new valve, is one inch below the toilet lever or handle on the left side of the toilet tank.
    • Cut the tube to the correct height, before putting the hose back on. The manufacturer's instructions will specify what that height is. For example, with a Fluidmaster 507A/B/D flush valve, you'll want to cut the overflow pipe so it's at least one inch below the hole in the tank where the flush lever is mounted.
  2. Once the flush valve is in the hole, attach a new thick rubber gasket (the same type as you removed). Then, hold the valve steady and replace the attaching nut, screwing it tight with your hands.
  3. Replace the hose, attaching it to the black plastic tube extending from the top of the flush valve.
  4. Turn the toilet tank right side up, and put it back on the toilet carefully, in order to avoid damaging any of your recently installed parts. [6]
    • Put the old nuts back on to make the tank sits snug on the toilet.
    • If you have purchased a toilet kit, use the new screws it includes.
  5. The supply hose located on the bottom of the toilet tank should be reattached to the toilet at this point, to restore water flow. It has a plastic nut on the end with threads. [7]
    • Connect it to the filler valve (looks like a little white tube) by threading the nut and bolt by hand.
    • Then, use a wrench to tighten the nut a quarter of a turn. Do not overtighten.
  6. Advertisement
Part 3
Part 3 of 3:

Testing and Troubleshooting

PDF download Download Article
  1. Flush the toilet a few times to check for potential leaks that may have developed. If the toilet has a leak, it will leak immediately.
    • Get under the toilet with a flashlight and see if the toilet is dripping.
    • Identify where the leak is coming from. Generally, water could be coming from the supply line or from a leaky gasket.
    • Shut off the water to check over the conical gasket and the supply line attachment.
    • Inspect and tighten the connections to address leaks.
  2. The water level should usually line up with the water mark on the inside of the toilet bowl. If water does not rise to the right level in the toilet, adjust the filler valve.
    • You can adjust the filler valve dramatically by moving the entire valve up or down. For minor adjustments, use the filler valve's screw.
  3. If you hear a whistle or noise that sounds like air leaving a balloon, then the flapper valve is not closing. Make an adjustment to slightly raise or lower the valve. The screw for the flapper valve is usually found on the float that looks like a little barrel that moves up and down with the water level.
    • Use a screwdriver to adjust the flapper valve's screw, tightening or loosening until the noise ceases.
  4. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do I detect a water leak?
    David Balkan
    Professional Plumber
    David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award.
    Professional Plumber
    Expert Answer
    The easiest method for detecting water leaks involves utilizing common tools such as water meters and specialized leak detection devices. By observing the water meter while water is not being used in the household, any movement indicates a potential leak, typically stemming from a running toilet. To verify this, one can isolate the toilet's water supply and observe the meter for continued movement. If the meter persists in registering usage, it indicates an internal leak, often located within concealed pipes beneath the floor slab or walls. For leaks suspected to be behind walls, simple listening devices like Aqua Phones can amplify sounds, aiding in detection. However, it's worth noting that homeowner proficiency with such devices may vary, and success rates can be limited. These Aqua Phones are primarily designed for identifying dampness, moisture, and mold, but they may also pick up the distinctive hissing sound of running water associated with leaks. Overall, these methods rely on auditory cues to pinpoint the source of leaks within a structure.
Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about plumbing, check out our in-depth interview with David Balkan .

      About This Article

      Thanks to all authors for creating a page that has been read 60,846 times.

      Did this article help you?

      Advertisement