Download Article
Download Article
Replacing window trim not only improves your home’s appearance, it also insulates it from the rain and cold. To begin replacing the trim, carefully pull the old trim off and use it as a guide to cut the new trim to size. Installing the new trim is as simple as nailing it onto your house and sealing the edges with caulk. Then you can fill in the nail holes with putty and paint the trim to make it look perfect around your window.
Steps
-
Pry off the old trim with a pry bar. To avoid damaging the wall, hold a wood block against it. Rest the back of the pry bar on the wood block. Slide the front end of the pry bar between the trim and the building, then pry off the pieces of trim and underlying trim boards. [1] X Research source
-
Use expanding foam to fill in wall gaps. On older houses, you may notice a gap around the window where the trim was. Put on a pair of gloves to cover your hands, then spray a thin layer of expanding foam into the gap. Let it expand and harden for about 20 minutes before continuing. [2] X Research sourceAdvertisement
-
Apply flashing over the exposed wall if it isn’t already there. Get a roll of adhesive-backed window flashing from the home improvement store. Cut the flashing to size, then peel off the backing to stick the flashing in place. Start with the top and bottom edges, wedging them under the building's boards and window siding as much as possible. [3] X Research source
- The flashing makes the trim and window more waterproof.
Advertisement
-
Measure the dimensions of the window. Go around the window with a tape measure to figure out what length of trim you need. Use the old trim as a guide if you still have it on hand. Mark your measurements on the trim pieces with a pencil. [4] X Research source
-
Put on safety glasses and a dust mask before cutting the trim. Wear polycarbonate safety glasses or a facemask to protect your eyes. Cutting the trim creates dust, so put on a mask or respirator to avoid breathing it in. [5] X Research source
- Wear earplugs or earmuffs to protect your hearing.
- Avoid wearing loose clothing when using a saw.
-
Cut the trim to size with a circular saw. Carbide-tipped saw blades will give you a smooth cut. Use the circular saw to cut off the excess ends of the trim. Make straight cuts so the trim pieces can lay flush against one another. [6] X Research source
- Remember that it’s better to keep the trim longer rather than shorter. You can adjust it as needed later.
- To make the trim more decorative, you can cut the trim at a 45° with a miter saw .
Advertisement
-
Pre-drill nail holes in the trim. Drill the holes through the outside surface of the trim. Drill a single hole at both ends of the trim. You’ll need to space out 2 more holes between them. Measure along the length of the trim so all the holes are an equal distance apart. [7] X Research source
- For example, if the trim is 16 in (41 cm) long, drill the holes every 4 in (10 cm).
- Pay close attention to the way you install the trim to make sure it isn't backwards or upside-down. [8]
X
Expert Source
Michael Fox
Window Repair Specialist Expert Interview. 1 December 2020.
-
Nail the trim to the wall. Get enough 2.5 in (6.4 cm) nails for all the holes in the trim. Start by placing the top piece of trim on the wall. Make sure it’s level before nailing it in place. Then fit the side and bottom trim pieces as close together as possible before fastening them to the wall. [9] X Research source
- If you’re working with PVC trim instead of wood, use steel trim-head screws instead.
-
Fill the nail holes with painter’s putty. Push putty or a paintable caulk into the holes. Use a putty knife to smooth the filler material and scrape off any excess. You’ll then need to wait for it to dry. If it still doesn’t look level, sand down the excess filler with 120-grit sandpaper.
- Check the label on the putty or caulk to figure out how long it takes to dry. [11] X Research source
-
Prime and paint the trim as needed. If you’re painting wood, brush on a coat of primer and let it dry overnight first. Paint the trim, including the filler in the nail holes, with small, even brush strokes. You can also color wood with a wood stainer instead of paint. [12] X Research source
- If you’re painting or staining wood, it’s recommended that you apply a wood sealant after painting to protect the trim from water damage.
- Cover bushes and grass with a tarp to protect them from damage. Wipe up any dripping paint immediately so it doesn’t have a chance to dry.
Advertisement
Expert Q&A
Search
-
QuestionWhat are some mistakes you see when people are replacing the trim on their windows?Michael Fox is a Window Repair Specialist and the President at Window Repair Systems and WindowHardwareDirect.com, based in Westminster, South Carolina. With over 25 years of experience, Michael specializes in commercial window repair and service. He holds a business degree from Monroe Community College and SUNY Brockport. Michael has helped Window Repair Systems and WindowHardwareDirect.com become an industry leader in commercial window repair and hardware distribution, servicing schools and businesses and training large public school systems.I've seen people installing them backwards, people installing them upside down, or using the wrong material so then moisture gets inside.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Things You’ll Need
- Prybar
- Trim
- Circular saw
- Drill
- 2.5 in (6.4 cm) nails
- Painter’s putty
References
- ↑ https://homesteady.com/how-6705923-exterior-door-window-trim-replacement.html
- ↑ http://www.frugalwoods.com/2014/07/30/how-to-replace-exterior-window-trim/
- ↑ http://www.frugalwoods.com/2014/07/30/how-to-replace-exterior-window-trim/
- ↑ http://www.homeadditionplus.com/dev/windows/replacing-exterior-window-trim/
- ↑ https://www.familyhandyman.com/carpentry/trim-carpentry/cutting-installing-plastic-trim/view-all/
- ↑ https://www.familyhandyman.com/carpentry/trim-carpentry/cutting-installing-plastic-trim/view-all/
- ↑ https://www.familyhandyman.com/carpentry/trim-carpentry/cutting-installing-plastic-trim/view-all/
- ↑ Michael Fox. Window Repair Specialist. Expert Interview. 1 December 2020.
- ↑ https://homesteady.com/how-6705923-exterior-door-window-trim-replacement.html
About This Article
Thanks to all authors for creating a page that has been read 87,511 times.
Advertisement