PDF download Download Article PDF download Download Article

If you suspect that your light switch may be faulty, you can do a simple test to find out. Many people automatically shy away from electrical work and it can be dangerous, so it's worth hiring a professional electrician to do this for you. However, you can safely do this task yourself as long as you turn off the electricity to your switch before working on it. With a few simple tools and some basic safety precautions, you can troubleshoot your light switch.

Method 1
Method 1 of 3:

Removing the Light Switch

PDF download Download Article
  1. You do this by accessing the correct circuit breaker and switching it to the “off” position. Circuit breakers are usually found in basements or closets, behind an electrical panel door. If you’re lucky, your breakers are labeled so you can easily identify which circuits they each operate. [1]
    • If you’re unfamiliar with how your circuits are wired, you can flip each breaker until you find the one that shuts off the circuit you need to access.
  2. Most light switches are covered by a decorative panel. You will need to remove this in order to access the switch. Remove the screws that hold the panel onto the wall. If the screws have one groove in the head, you’ll need to use a flat-head screwdriver to remove them. If they have something that looks like a star or cross on their head, you’ll need to use a Phillips-head screw driver. [2]
    • Keep your screws and panel cover together and place them out of your way. Unless you’re replacing the cover, you’ll want to put these back on at some point.
    Advertisement
  3. Whenever you work with electricity, caution is important. Use a non-contact voltage tester to make sure you’ve shut the power off to your switch. These work simply by moving them around near the terminals of your switch. [3]
    • Wave the voltage tester all around the front and sides of the switch without making direct contact.
    • If it beeps, you should stop working on the switch immediately and shut the power off before proceeding.
  4. Once you’ve confirmed that there’s no electrical current in your switch you are ready to remove it. Your switch may be attached to a frame by screws which you’ll need to take out, or it may just be sitting up against the wall.
    • Depending on how long it’s been there, you may have to apply a little elbow grease to pry the switch out of the wall. [4]
  5. Loosen any terminal and grounding screws with your screw driver. You want to loosen them just enough so that you can remove the wires that are attached. [5]
  6. Advertisement
Method 2
Method 2 of 3:

Testing Your Switch with a Voltmeter

PDF download Download Article
  1. These are the screws that attach your switch to the wiring in the wall. You will find these on the sides of the switch. [6]
    • The most common switch will have two screws on one side, these are the electrical terminals. [7]
  2. It doesn’t matter which lead wire you place on which screw. Once you have the lead wires in place, you should have a completed circuit and your voltmeter should flash and/or beep. [8]
    • A voltmeter will have an indicator light, an alarm sound, or both. This will alert you when the unit’s two lead wires complete a circuit. [9]
    • Voltmeters generally require batteries to function. [10]
  3. If you don’t get any response from the voltmeter, your switch is broken and will need to be replaced. If you do get a positive indication from your voltmeter that means your switch is working.
    • If you continue having difficulties once your switch has passed the test, that could mean you have a bigger electrical problem in your home. Turn the power off to that circuit and call a professional electrician to do additional testing for you.
  4. Advertisement
Method 3
Method 3 of 3:

Testing Your Switch with a Continuity-Tester

PDF download Download Article
  1. These are the screws that attach your switch to the wiring in the wall. You will find these on the sides of the switch.
    • The most common switch will have two screws on one side, these are the electrical terminals. [11]
  2. Your tester will have a long metal terminal and a lead wire. Use these to complete a circuit with the switch. It doesn’t matter which screw touches the tester terminal and which one touches the lead wire. The main thing is to make sure you have completed the circuit.
    • Once both pieces of the tester are in place, you should get a reading in the form of a flashing light, a beep, or digital readout with a positive number. [12]
  3. Your tester will measure the resistance in an electrical circuit and will let you know if your circuit is broken. Since resistance is measured in ohms, these are sometimes called “ohmmeters.” [13]
    • If your continuity tester gives you a number at or very close to 0, that’s an indication that current cannot flow through your circuit and the switch is broken. [14]
    • If you continue having difficulties once your switch has passed the test, that could mean you have a bigger electrical problem in your home. Turn the power off to that circuit and call a professional electrician to do additional testing for you.
  4. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you test a light switch with a multimeter?
    Richard Taylor
    Electrician
    Richard Taylor is an Electrician and Owner of R H Taylor Electrical Services based in Vero Beach, Florida. Richard has over 35 years of professional experience. He and his team offer electrical installation, re-wiring, and repair services.
    Electrician
    Expert Answer
    Set the multimeter to ohms. When you move the switch on, make sure that there's a clear path of resistance between the two poles; when you move the switch off, make sure that the circuit opens.
Ask a Question
      Advertisement

      Tips

      • The most important thing when working with electricity is to make sure you turn the power off before you touch anything.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • If your switch tests out ok but you continue to experience electrical difficulties, contact a professional electrician as this could indicate that there is a problem with the wiring in your home.
      • It’s important to make sure you can positively identify the correct circuit breaker for the switch in question. If you have difficulty, consult a professional electrician before proceeding.
      Advertisement

      Things You’ll Need

      • Flat-head screwdriver
      • Phillips-head screwdriver
      • Voltmeter/continuity tester
      • Non-contact voltage tester
      • Needle-nose pliers

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about electrical maintenance, check out our in-depth interview with Richard Taylor .

      About This Article

      Thanks to all authors for creating a page that has been read 41,211 times.

      Did this article help you?

      Advertisement