PDF download Download Article PDF download Download Article

Using a staple gun is a great way to fire a lot of staples super quickly. But getting a staple jammed in the gun can really disrupt your flow, especially if you still have a lot left to staple. Fortunately, unjamming a staple gun isn’t hard, and you only need a screwdriver and a pair of needle-nose pliers to fix most models. If you have any concerns, consult your owner’s manual to figure out what your staple gun needs.

Method 1
Method 1 of 5:

How do you unjam a heavy duty staple gun?

PDF download Download Article
  1. This rod runs the length of the magazine, pushing staples up and feeding them into the gun’s chamber. Look for a knob or tab at the bottom of the staple gun which is connected to this rod. Simply grab it and it and pull to slide the rod out, then set it aside. [1]
  2. Use a screwdriver to remove the screw at the bottom of the stapler. Once the screw is out, reach in and remove the staple gun’s magazine. It should slide right out without any problems. [2]
    Advertisement
  3. Check out the top of the stapler where the staples are discharged. Use the pliers to pinch the staple and pull towards you, pulling the staple out of the stapler’s nose. After that, reassemble the staple gun by putting the magazine back in and screwing in the screw. [3]
  4. Advertisement
Method 2
Method 2 of 5:

How do you unjam a hammer stapler?

PDF download Download Article
  1. Hold the stapler at eye level and look for the metal base on the very bottom. Simply grab the bottom and pull the pusher out, then set it aside. [4]
  2. The pin is on the bottom of the stapler right above the pusher mechanism you just pulled out. Push the point of the screwdriver onto the pin, then grab it and slide it out of the stapler. [5]
  3. The magazine is the long metallic piece at the front of the stapler that does the actual stapling. Now that it’s loose, simply slide it out of the stapler and check for jams. Remove any staples that are stuck using needle-nose pliers. [6]
  4. Advertisement
Method 3
Method 3 of 5:

How do you unjam an electric staple gun?

PDF download Download Article
  1. Unplug the staple gun before you try to fix it to avoid any injuries. Look for the release lever on the very bottom of the staple gun. Pull on the lever to unclip the magazine, then pull the magazine out of the gun. [7]
  2. Some jams are caused by staples failing to properly leave the magazine. If you notice your staples are crushed by other staples, use needle-nose pliers to gently unstick the jam. [8]
  3. Check out the discharge area to look for staples that aren’t in the magazine, but haven’t actually discharged. Use a pair of needle-nose pliers to reach the jam and pinch the staple to remove it. Work slowly and try to be gentle so you don’t accidentally damage the staple gun in the process. [9]
  4. Advertisement
Method 4
Method 4 of 5:

Why does my stapler keep jamming?

PDF download Download Article
  1. Firing a staple gun super quickly can cause the staples to stack on top of each other and jam the gun. If your staple gun jams a lot, slow down your stapling to a more moderate pace. [10]
  2. Staples come in different sizes (usually small or large). If you’re using the wrong size, it could cause your gun to jam. Check the owner’s manual to find out which staples you should be using for a smooth stapling experience. [11]
  3. Advertisement
Method 5
Method 5 of 5:

Which way do the staples go in?

PDF download Download Article
  1. It’s easy to put the staples in upside down and accidentally jam the stapler. Slide your staples into the magazine with the flat side down and the sharp edges pointing upward. [12]
    • This is true for most staple guns, but it could vary depending on the model you have. If you’re not sure, check your owner’s manual.
    • Be sure to note the end of the staple gun where the staples are supposed to come out of, since it's not always located where you might think.
    • The tool is often marked with an arrow of where the staples will come out.

Expert Q&A

Search
Add New Question
  • Question
    How do you stop a stapler from jamming?
    Sarah Fogle
    DIY Specialist
    Sarah Fogle is a DIY Home Improvement Specialist and the creator of Ugly Duckling House. With over a decade of experience, Sarah specializes in beginner-friendly home remodeling projects. Sarah holds an MBA from Georgia State University. She has been featured in multiple publications including Better Homes and Gardens and Make Magazine. She has also partnered with brands such as Lowe's, Home Depot, and Martha Stewart Crafts.
    DIY Specialist
    Expert Answer
    To avoid that, I always load my staple gun from the back using a full sleeve of joined staples, since using smaller broken bits of staples tends to jam more.
Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Warnings

      • If you’re working with an electric staple gun, make sure it’s off and unplugged before you start taking it apart.
      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 66,762 times.

      Did this article help you?

      Advertisement