Download Article
Download Article
There are a few ways of untying your favorite balloons. For those who plan ahead, there are easier ways of preparing your balloon to be untied. Both amateur and professional balloon handlers pop balloons in this process. It'll take time to successfully master the untying process. Be patient and be prepared to pop a balloon or two.
Steps
-
Inspect the knot. Look closely at the balloon knot and find where it rolls over itself. -
Pull out the bottom half of the knot. You must be careful in this process. You want to be able to see the area where you'll be able to slide your fork into.Advertisement -
Slide one of the fork prongs through the knot. Unless the knot is super tight, it should slide through real easy.- Careful not to pierce the balloon at this stage.
-
Use a knitting needle. This works even better than a fork prong. Thick needles with a blunt, rounded point are the best. Moisten the needle a little bit by licking it for easier access.- The edge of a knitting needle is pointed enough to get into that tight little spot.
- But it is not sharp enough to pop the balloon.
- You can use it to loosen the knot and untie it.
-
Pull the knot out. Use either the needle or fork to roll the knot out. You can help by trying to push the knot while sliding it down. -
Try again. If it doesn't unroll the first time, slide it back up and repeat this process.
Advertisement
-
Position the balloon. Hold the balloon so the inflated portion is wedged into your lap. Secure the balloon gently but firmly using your thighs. -
Inspect how the knot is formed. Try to follow where the knot loops around itself. Visualize how the knot was formed. -
Push and pull the knot. The ultimate process of loosening the knot is to push and pull various sides of the knot. Continue this until you are able to get part of the knot to yield.- Focus on particular loops of the knot when pushing and pulling. The goal is to loosen and grip a single strand of the knot.
-
Separate a strand with your finger. Lodge your fingernail into one of the loops. Try to get a secured grip of that particular loop. You'll need to work on loosening the knot for a while before you can secure a section of the knot.- This is easier if your fingernails are long.
-
Pick the connecting knot. Once you grip a strand of the knot, locate its connecting loop. Using your other hand, pry out the folded loop underneath the other loop. By prying one loop of the knot with one hand, you should be able to loosen this part of the knot. [1] X Research source -
Use your tooth to loosen the knot. Once you've separated two loops of the knot, there should be a small opening. Wedge your fang tooth into the opened crevice. By pulling with your hands, gently, the knot should loosen and untie.
Advertisement
-
Inflate your balloon. Be sure it is full but not overly full. Inflate it 3/4 of the way full. -
Use a rubber band. Twist the neck several times so it is well sealed. Stretch out the balloon with one hand. Wrap a rubber band around the neck, and tuck it into the other end of the rubber band. Pull the longer end tight. [2] X Research source- This knot is called a lark's head knot. The goal is to use the rubber band as a tightening agent.
- For increased support, you could tie the rubber band as well. This could be just as challenging to untie as a regular balloon's knot.
-
Use a twist tie. One of the easier ways of deflating your balloon without popping it is to use a twist tie. Simply hold the neck tight with one hand, and then begin securing the neck with a twist tie. -
Use a clothespin. Do the same process as above, only this time secure the balloon with a clothespin. Be sure the clothespin is fresh and sturdy, or else it might not hold the air well. -
Tape the balloon's end. Have a few strips of tape ready to be used. Grip the neck of the inflated balloon with one hand. Then tape off the ends using your strips.- Use scotch tape for the best results.
Advertisement
Community Q&A
Search
-
QuestionWhy, when I put the fork prong through, is it covered in latex?Community AnswerThis is because you are pushing against the latex! You have to push through the different sections of latex, not through one. That would result in a hole in your balloon!
-
QuestionHow do I untie a balloon at school?Community AnswerHold just above the knot airtight so no loud noise is made when you finish. Push one end of the rubbery material through the loop, and pull out on the other side. Now you should be holding a an untied balloon. Slowly let the air out, careful not to make any noise, and hold it tightly so that it doesn't escape and fly around the room.
-
QuestionCan I use a lock pick? If so, how?Community AnswerIt depends on the thickness. It must be thin enough to fit through the knot. But if you are using wire or a bendy object, I say you should use something else. If the item that you are using is bendy, it may be hard to slip it through. If you have big fingers, use something thick enough to get a grip on with your hands. Make sure that your lock pick is mostly a straight line, as it may be hard to handle a wavy or spiky one.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Things You'll Need
- Balloon
- A fork, or a knitting needle
- Rubber band or hair tie
- Scotch tape
- Clothesline
- Twist ties
References
About This Article
Article Summary
X
To untie a balloon, gently push and pull on the knot to loosen it. You can also use your teeth to pull on one of the strands of the knot so it's easier to untie. If you're still struggling, try sliding the prong of a fork or a knitting needle under one of the strands of the knot. Then, use the space you've created with the fork or needle to pull the knot apart. If you want to learn how to temporarily tie a balloon so it's easier to untie, keep reading the article!
Did this summary help you?
Thanks to all authors for creating a page that has been read 143,077 times.
Reader Success Stories
- "Well, at first it was a bit hard, but as the steps got higher, it made more sense. If you follow the directions correctly, you will be able to do it right!" ..." more
Advertisement
"Well, at first it was a bit hard, but as the steps got higher, it made more sense. If you follow the directions correctly, you will be able to do it right!"
..."
more
"It was hard and a bit painful to the fingers but you will get the satisfaction of an untied balloon in the end."
"It helped because my lil sis tied my balloon in a knot. I told my mom but no one could untie it..."
