Download Article
An easy step-by-step guide so your pup can stay warm all winter long
Download Article
Did you know dogs could get hypothermia and frostbite in extreme weather? If your dog stays outside for long periods, then they need proper shelter.
Steps
Download Article
-
Determine the size of the doghouse: Measure your dogs length, then add 12” to determine the width of the doghouse. Add 18” to determine the length of the doghouse. Measure your dog's height, and then add 9” to determine the front of the doghouse and add 3” to determine the height of the back of the doghouse. -
Once you have determined the size the doghouse, begin by cutting the floor joists using the 2x4's. You will need to cut two joists for the length of the doghouse and three for the width. Butt the length parts up to the width parts making a rectangle. Screw ends together using 3” exterior screws. Center the third width part in the rectangle and screw to secure it. Now you have the frame of the floor of the doghouse.Advertisement -
Cut ¾ plywood to fit over floor frame. Screw down to floor frame using 1 ¼ exterior screws. Flip floor over to expose floor framing. Cut 1” foam insulation board to fit between floor joists. Use liquid nails to secure foam insulation board. -
Now to build the sidewalls. Cut ¾ plywood to the width of the doghouse. Measure along the left side, using the measurement determined in step 1 for the front of the doghouse and add 3 ½” to allow coverage of the floor 2x4. Make a mark on the measurement. Then, measure the left side using the measurement determined in step 1 for the back of the doghouse. Be sure to add 3 ½” for coverage of floor 2x4. Mark on the measurement. Next, take a straight edge, line it up to the two marks, and draw a line. Cut along line. This determined the angle of the sidewall. Trace the sidewall on the ¾" plywood and cut to make the other sidewall. This making both sidewalls the same. -
Screw sidewall to the floor using 1 ¼ “ exterior screws. Cut a 2x2 for each corner, the same angle as sidewall. Attach 2x2's to each corner. Cut front and back panels using the ¾” plywood. Attach only the back panels using 1 ¼" exterior screws. Now cut 2x2 for the top and bottom of the front and back panels. Attach to the back only, this will give you a place to screw the interior plywood to the walls. -
Following the manufactures instructions for cutting hole for the dog door. Screw front panel on doghouse and install dog door. -
Cut 1” and ½ “ foam insulation board to fit inside walls, The 1” and ½ “ foam should be flush with the 2x2's on the interior. Now cut ¾" plywood to fit all four of the interior walls. Screw the plywood to the 2x2's using 1 ¼" screws. -
Build the roof. Cut roof out of ¾ “plywood. Be sure to leave an overhang to keep rain away from walls. You will need to cut two the same size to insulate it. Cut 2x2 for edge, this will give a place to put the foam insulation and screw the two peaces together. A piano hinge can be installed on the back and roof to make the doghouse easier to clean. -
Shingle the roof. Apply water-resistant felt paper and drip edge. Now, nail asphalt shingles on making sure the shingles do not line up. -
Drill a hole in the back of the doghouse in the corner, down near the floor. This hole needs to be just big enough for the end of the cord to the heated mat to go through. Lay the mat down on the floor and put the cord through the wall. Be sure the cord is all the way outside to prevent dog from chewing it. There you have an insulated and heated doghouse.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Paint the plywood or install vinyl siding to protect the walls.Thanks
- The electric heated mat can be replaced with a self-heated bed. They are made of special material that holds in your dogs own body heat.Thanks
- Cover cord of the heated mat with PVC pipe to prevent the cord from being chewedThanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Always use protective eye gear when using power tools.Thanks
- Check local codes to make sure extension cords are allowed if the doghouse is not near enough to the electrical outlet.Thanks
- Plug heated mat into a ground-fault circuit interrupter (GFCI). GFCI is a special electrical outlet that prevents electrical shocks and fires.Thanks
Advertisement
Things You'll Need
- 2x4"'s
- 2x2"'s
- 3/4" plywood
- Liquid Nails
- 3" exterior screws
- 1 1/4" exterior screws
- Roofing nails
- 1" foam insulation board
- 1/2" foam insulation board
- Piano hinge
- Water resistant felt paper
- Drip edge
- Dog door
- Heated mat
About This Article
Thanks to all authors for creating a page that has been read 132,260 times.
Advertisement
