How to Remove Keyboard Caps to Clean Them

Follow these best practices to keep your keys clean

Co-authored by Kadi Dulude and Mason Martinez, BA

Last Updated: April 15, 2024 Fact Checked

If you spend a lot of time at a computer, you may have noticed that your keyboard doesn’t look as clean as when you first started using it. Dust, food particles, and oils from your fingers may have left the keys looking pretty grimy. If you’re using a mechanical keyboard, it's easy to clean the keycaps. We'll show you the best—and easiest—way to clean your keys, below.

Quick Tips for Washing Keycaps

Disconnect your keyboard and use a wire keycap puller to remove the keys. Spray the keyboard with compressed air to remove debris.
Soak the keycaps in warm, soapy water for 30 minutes. Add 2 denture tablets if your keys are really dirty. Put the keycaps in a strainer and rinse them.
Air dry the keycaps for at least 24 hours before popping them back in their correct positions. Dust your keyboard weekly and deep clean once a month.

1

Remove the keycaps.

Download Article

Unplug and use a keycap puller to lift the keys from the board. Take a photo of your keyboard to remember where each key goes before proceeding. For wired keyboards, unplug the wire from the USB port. Purchase a keycap puller to pinch and pull the keys from their slots. ^{[1]
X
Research source} Avoid removing large keycaps, like the spacebar, enter, and shift.
- Wire keycap pullers are less likely to scratch the keys than plastic ones. ^{[2]
  X
  Research source} Place the wire loops diagonally on the key and gently wiggle back and forth while pulling up.
- A keycap puller can be substituted for a tweezer, flathead screwdriver, butter knife, or bent paperclip.
- Remove keycaps without a tool by pinching the sides of each key with your finger and pulling up.
- If you can’t take a picture of your keyboard, look up an online image of the same or similar keyboard.

2

Spray debris away, if necessary.

Download Article

Remove debris, dust, and crumbs with compressed air. To ensure your keyboard works effectively, take a can of compressed air and insert the thin straw applicator into the can’s nozzle. Perform a test spray. Hold the can upright as you spray the keyboard and stems, using short bursts to remove any lingering debris. ^{[3]
X
Research source}
- Use a damp microfiber cloth or a soft-bristle toothbrush as a substitute for compressed air. ^{[4]
  X
  Research source}

3

Soak the keycaps in soapy water.

Download Article

Place the keycaps in a bowl of warm, soapy water for 30 minutes. Fill a bowl or container with warm water and a few drops of mild soap. Mix it until bubbles form. Place the keycaps in the solution, ensuring they’re fully submerged. You can also add 2 denture tablets to help remove oils from the caps. ^{[5]
X
Research source}
- Avoid using hot, boiling water or bleach, which can cause the keys to fade.
- Some users say to let the keycaps soak for 5 to 6 hours, while others say 30 minutes is sufficient. Start with 30 minutes, then check the keys and decide how much longer you want to soak them. ^{[6]
  X
  Research source}

4

Scrub and rinse the keycaps.

Download Article

After soaking, use a soft-bristle brush or cotton swab to loosen stubborn gunk. Avoid brushing the switch stems, the long stems within the switch housing, or the spring. ^{[7]
X
Research source} This will keep particles from becoming lodged too deep. Put the keys in a strainer and rinse them thoroughly. ^{[8]
X
Research source}

5

Let the keycaps air dry completely.

Download Article

Lay the keycaps on a flat surface with the stems up while they dry so the water can evaporate. Use a microfiber cloth to dry the keys instead of paper towels since they can leave small particle residues that cause scratches. ^{[9]
X
Research source}

6

Reassemble your keyboard.

Download Article

Match the placement of the keycaps to the photo of your keyboard. Ensure all the keys are placed back in their respective spots and facing correctly. To pop the keycaps back on, push them straight down over the switch with your fingers. Plug the board back in when you’re ready, and test each key to ensure everything is working properly. ^{[10]
X
Research source}
- Clean your keyboard once a week without removing the keycaps. Use a handheld vacuum, a damp microfiber cloth, or compressed air. Perform a deep clean once a month.
- Disinfect your keycaps with hydrogen peroxide or alcohol wipes.
- Avoid eating or drinking near your keyboard to prevent crumbs and other build-ups.

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

Log in

How to Remove Keyboard Caps to Clean Them

Quick Tips for Washing Keycaps

Steps

Remove the keycaps.

Spray debris away, if necessary.

Soak the keycaps in soapy water.

Scrub and rinse the keycaps.

Let the keycaps air dry completely.

Reassemble your keyboard.

Expert Q&A

Video

Tips

You Might Also Like

References

About This Article

Reader Success Stories

Did this article help you?

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories