How to Clean a Roborock Sensor

PDF download Download Article
PDF download Download Article

Roborock robotic vacuum cleaners make cleaning your floors convenient and hassle-free. To keep your Roborock working properly, clean the sensors once a week. The sensors are your Roborock’s “eyes” that let it see where it’s going as it’s cleaning your floors. If they get dirty, your vacuum might start bumping into objects, missing spots, and not charging properly. Cleaning the sensors is super easy and all you need is a soft cloth.

Method 1
Method 1 of 2:

Best Practices

PDF download Download Article
  1. A dry cloth is all you should need to remove dust and other debris that’s blocking the sensors on your vacuum. A microfiber or cotton cloth will do the trick. Don’t use anything abrasive to clean the sensors, like paper towels or the rough side of a sponge, since it can scratch them. [1]
  2. Roborock advises against using anything damp to wipe down any part of a Roborock vacuum, including the sensors. If liquid gets inside of your vacuum, it could damage it. [2]
    • If the sensors are particularly dirty and a dry cloth isn’t helping, you could try using a slightly damp cloth to wipe down the sensors. However, this could potentially damage the sensors and void any warranty you have on your vacuum, so proceed with caution.
    Advertisement
  3. When dirt and debris accumulate on the sensors, your vacuum will stop working properly. To prevent this, try to remember to clean the sensors at least once per week. Consider cleaning them after every use so you don’t forget. [3]
    • Clean the other components of your Roborock on a regular basis too, like the dustbin, filter, wheels, and main brush.
    4. Advertisement
Method 2
Method 2 of 2:

Wiping Down the Sensors

PDF download Download Article
  1. Flip your Roborock over. Then, locate the 4 sensors running along the edge of the front half of the device. These are the drop sensors. Take your soft, dry cloth and gently wipe off each sensor. [4]
    • The drop sensors will be slightly sunk into the plastic that’s covering the bottom of the vacuum. They’re each about 1 inch (2.5 cm) long and they’re reflective.
    • Different models of Roborock vacuums may have slightly different layouts. If you’re having a hard time locating any of the sensors, refer to the owner’s manual or look up a diagram of your specific model online.
  2. These are the sensors that help your vacuum determine how far it is from nearby walls. Look for a small oval-shaped sensor on each side of your vacuum. These are the distance sensors. Wipe them down with the dry cloth to remove any dust and debris. [5]
  3. The contact sensors are the small square sensors located on either side of the front wheel. They make contact with the terminals on the docking station when you’re charging your Roborock. Gently wipe off these sensors with the dry cloth. [6]
  4. These sensors help your Roborock enter the docking station and avoid objects while it’s running. The dock-station return sensor is a narrow, horizontal oval that’s centered on the front bumper. The collision sensor is a long, narrow sensor that runs along the bottom edge of the front bumper. Wipe both of these sensors down with the dry cloth. [7]
    5. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Video

      Tips

      • Try to clean your Roborock’s sensors once per week so they don’t accumulate too much dust and debris. The cleaner the sensors are, the better your vacuum will function. [8]
        Thanks
        Helpful 2 Not Helpful 1
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      You Might Also Like

      How to
      Locate, Remove & Clean a Dirty MAP Sensor
      How to
      Clean a Mousepad: Fabric, RGB, & Plastic
      The Best Ways to Clean Your Headphones and Earbuds
      How to
      Clean Electrical Contacts
      How to
      Clean and Maintain an iPad Screen
      3 Helpful Ways to Keep Dust Out of Your Computer
      How to
      Clean a Typewriter
      How to
      Clean a Projector Screen
      How to
      Clean a PopSocket
      How to
      Clean a Fitbit
      Advertisement

      References

      1. ↑ https://images-eu.ssl-images-amazon.com/images/I/B1-udyGMQ0S.pdf
      2. ↑ https://images-eu.ssl-images-amazon.com/images/I/B1-udyGMQ0S.pdf
      3. ↑ https://us.roborock.com/blogs/blog/how-to-maintain-your-robot-vacuum
      4. ↑ https://support.roborock.com/hc/en-us/articles/360036039712-Roborock-S6-General-Maintenance
      5. ↑ https://us.roborock.com/blogs/blog/how-to-maintain-your-roborock-robot-vacuum
      6. ↑ https://support.roborock.com/hc/en-us/articles/360036039712-Roborock-S6-General-Maintenance
      7. ↑ https://support.roborock.com/hc/en-us/articles/4405762070553-Emptying-and-Maintenance-of-Roborock-Auto-Empty-Dock
      8. ↑ https://us.roborock.com/blogs/blog/how-to-maintain-your-robot-vacuum

      About This Article

      Thanks to all authors for creating a page that has been read 219,032 times.

      Did this article help you?

      Advertisement