Download Article
Download Article
When it comes to cars, a lot of maintenance requirements can be handled by yourself. By foregoing a visit to your local mechanic and maintaining your own car, you can save some cash. Even though some of the maintenance tasks can be difficult, especially for those people who are mechanically-challenged, learning how to clean a transmission can be a great step towards becoming a competent do-it-yourselfer.
Steps
Get Car Support Solve Any Problem
Try Asking:
We’re sorry we don’t support the car you are looking for. Please enter its make, model, and year below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
-
Warm up your vehicle by driving it around for a few minutes.- Draining the fluid will go much faster when the fluid is at least warm.
- Be careful working around hot vehicle components, especially the exhaust system.
-
Always work on a flat, regular surface. Place the vehicle in park, set the parking brake and chock the rear wheels before raising the vehicle.Advertisement -
Use your owner’s manual to locate a good jacking point and raise the vehicle high enough off the ground to clear your jackstands. -
Again referring to your owner’s manual, place jack stands on both sides of the vehicle. Jack stands allow for much easier access to the relevant components. Jack stands are also much more reliable. [1] X Research source -
Ensure you have the correct fluid for your vehicle. There are many types of fluid and some manufacturers even require brand specific fluid. Consult your owner’s manual and an automotive parts professional to ensure you have the correct fluid and parts before you begin.
Advertisement
-
Drain the fluid and remove the transmission oil pan. Position a large drain pan under the transmission oil pan and try not to spill any fluid. Keeping the area under your vehicle clean will help you stay clean. [2] X Research source- Look for a drain plug. The drain plug will usually be a standard threaded plug located in one corner of the transmission oil pan. Remove the plug and allow the fluid to drain, then reinstall the drain plug.
- If there is no drain plug, draining the fluid will be a little more tricky. Loosen all the bolts on the transmission oil pan and then completely remove the bolts from one side. This will allow the side or corner of the pan to drop enough so that the fluid will run out.
- After the fluid has drained fully remove all the bolts and make note of their location. Remove the transmission oil pan. It may need to be tapped loose with a rubber hammer.
-
Examine the old transmission fluid. Look for anything that seems out of place like sediment or large pieces of metal in the fluid. This could be indicative of a larger problem, so if you find anything, consult a transmission expert immediately. It is also a good idea to measure the amount of fluid drained because this will give you a good estimate on how much fluid to replace. [3] X Research source -
Clean the transmission oil pan inside and out. Automatic transmissions are very sensitive to dirt and foreign matter. Use a degreaser to clean the outside of the pan and brake cleaner to clean the inside and the gasket mating surfaces.- Carefully remove all the gasket material from the transmission oil pan and the mating surface on the transmission. A razor blade may be helpful.
- Most transmissions have a magnet in the pan to catch small metal particles. Be sure to clean and reinstall the magnet.
- Clean the bolts that secure the oil pan to the transmission.
-
Remove and replace the transmission filter. Most automatic transmissions have a filter that traps debris in the system and changing this filter is part of a complete service. [4] X Research source- Most transmission filters are located on the bottom of the valve body and are clearly visible once the transmission oil pan has been removed. Look for the white or yellow plastic mesh on the bottom of the filter.
- Some filters merely snap into place or are held on by clips. Pay attention to the location and orientation of the clips. It may be helpful to take a picture before removing to use as a reference.
- Other filters are held in place by bolts that can vary in length. It is imperative these bolts are reinstalled in their correct locations.
- Other transmissions employ external spin-on filters that resemble engine oil filters. Remove the filter with oil filter pliers and simply tighten the new one by hand.
- Apply a little clean transmission fluid on any o-rings or seals on the filter as this will make installation much easier.
- Most transmission filters are located on the bottom of the valve body and are clearly visible once the transmission oil pan has been removed. Look for the white or yellow plastic mesh on the bottom of the filter.
Advertisement
-
Reinstall the transmission oil pan. Work cleanly, slowly and carefully and this will be easy. [5] X Research source- Apply a light coat of high-tack gasket sealant to the transmission oil pan and then carefully place the gasket on the pan, lining up the holes on the gasket with the holes on the pan. Allow the sealant to set-up a few minutes so the gasket won't shift during installation. RTV silicone is NOT recommended for this application.
- Carefully reinstall the transmission pan on the transmission and reinstall the bolts. Tighten the bolts in accordance with manufacturer's specifications.
-
Raise the vehicle off the jackstands. Remove the jackstands and lower the vehicle. -
Open the hood of your vehicle and find your transmission dipstick. Typically the transmission dipstick is red in color, while the engine oil dipstick is yellow but always refer to your owner’s manual. The dipstick tube usually doubles as the fill port. Slowly refill the transmission fluid, checking the level often to avoid overfilling. A long funnel will make this easier. -
Start the engine when the transmission fluid begins to register on the dipstick. Let the engine idle for a few minutes and look for leaks. It is a good idea to move the selector lever through all positions as well. -
Top-off fluid and continue to check for leaks. Refer to your vehicle’s owner’s manual for exact instructions on how to check the fluid level. This is very important because some vehicles require you to check the transmission fluid with the engine running and others do not. Following the wrong procedure may result in an inaccurate dipstick reading. Ensure you’re using the right procedure and the level is correct and you’re all done!
Advertisement
Community Q&A
Search
-
QuestionWhat if I have to replace or repair the transmission?Community AnswerThe transmission is one of the most expensive parts of your car to repair. Find a reputable shop to give you an estimate on price, then decide if it's more cost effective to do the repair or replace the whole car. As a point of reference, I once paid about $3,000 to rebuild the transmission in a '99 Maxima.
-
QuestionHow do I clean out the fluid in the torque converter?Community AnswerYou would have to take the transmission apart to do that. When it doesn't work properly, then usually the torque converter is bad. (The gas mileage goes down and RPMs go up.) This can happen intermittently on the freeway as the torque converter is going bad.
-
QuestionWhat should I do if my transmission sometimes gets stuck and revs high?Community AnswerThe first thing to do is change the transmission oil. Most cars use a type of oil which has solvent mixed into the oil. As the solvent evaporates, the viscosity increases and the oil becomes too thick. On old cars, adding a transmission additive would work great in many cases. On a CVT Transmission, doing that would void the warranty. You might have a bad transmission.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Things You'll Need
- Jack
- Jack stands
- Socket set
- Drain pan
- Brake cleaner
- Degreaser
- Razor blade
- Rubber hammer
- Replacement transmission filter
- Gasket sealant
- Transmission fluid
References
About This Article
Thanks to all authors for creating a page that has been read 94,639 times.
Advertisement
90%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
