Sliding glass doors can become difficult to open because the track accumulates dirt and debris. The steps below tell you how to keep your sliding glass door sliding smoothly.
Steps
Use this method at least once a year to thoroughly clean and lubricate the track to your sliding door. If you have a screen door, remove it first—–it will easily lift up and out of the track.
-
Remove drapes, blinds or any other window furnishings from your door. -
Grasp each end of the door. Push the door up so that the wheels on the bottom of the door clear the track. You may have to use a screwdriver to loosen the level screws for the bottom wheels in order to get them to clear the bottom threshold.Advertisement -
Keep pushing the door upward. Pull it towards you at the same time until it clears the door opening. -
Place the door on two sawhorses so that you can clean the track wheels. -
Use a wire brush to loosen the hair and dirt from the wheels. -
Vacuum the debris from the wheels and the entire bottom and top of the door. -
Apply a non-stick silicone lubricant to the wheels. -
Test the rollers to be sure that they are clear of all debris and are moving freely. -
Vacuum the door track. -
Wipe out the door track with a wet rag. -
Apply some of the lubricant to the tracks in the door opening before you replace the door. -
Lift the door from the sawhorses. Position the top of the door inside the top track of the door opening. -
Push the door up so that the bottom rollers clear the bottom threshold. -
Let the rollers drop into the bottom track. If you have loosened any screws, retighten them once the door is completely back in its track to make sure the door is plumb. -
Slide the door back and forth until it is sliding smoothly.
Advertisement
If the track to your sliding door isn’t too gummed up with dirt and grime, you can get your door sliding smoothly again in about 15 minutes.
-
Thoroughly vacuum the track to your door while it is still closed. -
Slide the door all the way open so that you can access the other side of the track. -
Scrape out the dirt and debris from the track using a flat blade screwdriver. -
Vacuum the loosened dirt using an attachment with a narrow tip. -
Use an old rag to apply generous amounts of a non-stick lubricant to both tracks of the sliding door. -
Slide the door open and shut several times so that the entire track gets lubricated. You may have to open and shut the door for several minutes before it slides smoothly.
Advertisement
Community Q&A
Search
-
QuestionHow do I lubricate glass shower doors on a track?Community AnswerI would recommend a dry spray lubricant like wax. Home improvement stores sell spray cans that use a carrier solvent to dispense wax, which is left after solvent evaporates quickly. Wax doesn't attract sand/dirt like WD-40 does. Use wax lubricant on bike chains, too.
-
QuestionHow do I put a plastic shower back on track?Community AnswerUse a powder-quality graphite such as Monkey Dust or Hob-E-Lube. If you find that doesn't work sufficiently, then use a super lubricant like NyOil or Krytox. Just know that these will be oil-based and can be a bit messy.
-
QuestionMy sliding glass door will freeze shut in the winter. Is there something I can put on the track to prevent it?Community AnswerTry an aerosol silicone-based lubricant. Silicone does not freeze, so this may solve your problem.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- It also helps to lubricate the tracks to your sliding doors every few months.Thanks
- Be sure to clean the tracks on both sides of the door.Thanks
- Clean the track to your sliding door every few months with a wire brush. The brush will loosen stubborn dirt deposits, which you can then vacuum.Thanks
Tips from our Readers
The advice in this section is based on the lived experiences of wikiHow readers like you. If you have a helpful tip you’d like to share on wikiHow, please submit it in the field below.
- Try to keep the track as clean as possible. Adding too much lubricant to the track does collects dirt and grit, which shortens the life of the rollers.
- I like using very fine sandpaper to smooth out any nicks in the aluminum. After that, just wipe it clean with mineral spirits.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- It’s best to have a helper if you are going to remove your door from its tracks. If you should have to loosen screws, your helper can spot you and make sure the door doesn’t fall before you can remove it.Thanks
- Try to avoid oily lubricants because they attract dirt and dust; you’ll have to clean the rollers and tracks of your doors much more often if you use any kind of grease or oil instead of a non-stick lubricant.Thanks
Advertisement
Things You’ll Need
- Vacuum.
- Wire brush.
- Spray lubricant.
- Flathead screwdriver (optional).
About This Article
Article Summary
X
To quickly clean and lubricate a sliding glass door, start by vacuuming 1 side of track while the door is still closed. Then, slide the door all the way open, vacuum the other side, and scrape out the dirt and debris inside the track using a flat blade screwdriver. Afterwards, vacuum the loosened dirt, and use an old rag to apply non-stick lubricant to both sides of the track. Finally, slide the door open and shut several times to spread the lubricant over the entire track. To learn more, including how to clean the track wheels on your sliding glass door for a more thorough cleaning, read on.
Did this summary help you?
Thanks to all authors for creating a page that has been read 382,585 times.
Reader Success Stories
- "I liked how the article explained how to remove the sliding glass doors. I have always used the "quick method," but didn't know how to actually remove the doors to do a thorough cleaning of the tracks. Thank you for the explanation!" ..." more
Advertisement
"I liked how the article explained how to remove the sliding glass doors. I have always used the "quick method," but didn't know how to actually remove the doors to do a thorough cleaning of the tracks. Thank you for the explanation!"
..."
more
"The article explains the caking around the door wheels. This is probably where the problem is because the track is clean."
..."
more
"Having the right tools on hand, before I started the job. Sep by step instructions helped."
