PDF download Download Article PDF download Download Article

If you want a pair of bondage pants and can't afford to buy them, you can make your own without too much trouble. For a quick pair of pants, you can use safety pins. If you want a more permanent look, stitching up the pants with a needle and thread works quite well. Creating bondage pants on your own takes patience and ingenuity, but the results are worth it.

Method 1
Method 1 of 2:

Using Safety Pins

PDF download Download Article
  1. This is just going to be a mark so you know where to sew them later.
  2. Turn the pants inside out and peg them all the way up the inner seam - you can do this by hand with a needle and thread - it takes more time with than with a machine but it works. .
    Advertisement
  3. You can glue or stitch those on too. This allows you to get them looking exactly how you want.
  4. You can also just put the pants on and wrap all the loose fabric back really tight then, using safety pins, pin the loose fabric tight against your leg.
  5. Advertisement
Method 2
Method 2 of 2:

Using Stitches

PDF download Download Article
  1. The zippers are easy to attach just by doing a neat stitch to hold them down. Pin them in place before you start stitching. You might even want to try the pants on and mark with a safety pin exactly where you want them.
  2. Place one pair just below your waist and one just below you knee. Do this by putting 2 inches (5.1 cm) of webbing through the ring.
  3. {FIG. 2} Webbing has a tendency to unravel and this will help keep that from happening, it will also reinforce the rings. You want these to be as strong as possible! {Note: the rings on the above pants are actually turned the wrong way... this is so you can see their placement. The rings should be horizontal and the webbing holding them on going down the leg.}
  4. Depending on your height you'll want to make them about 2–3 feet (0.6–0.9 m) long. For every strap you'll need 3 feet (0.91 m) 1.5 inches (3.8 cm) webbing, and 2 clasps. These can be found at fabric stores, hardware stores, camping supply and military surplus stores, and in many hardware sections of discount stores like Walmart. Loop the webbing around the loop on the clasp, and do the square/X stitch as above. Do this on both ends.
  5. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What do you do with them?
    Community Answer
    You wear them! They may not be suitable for everyday wear, but they're great for going to a goth club, party, concert, etc.
Ask a Question
      Advertisement

      Tips

      • To add more creativity into your bondage pants, use brightly colored thread, such as neon or glow-in-the-dark green, blue, or pink.
      • You can also buy or make patches/buttons for your favorite bands
      • You might want to put the pants on first to see where you want to place things.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      Things You'll Need

      • Method One
        • Pants
        • Safety Pins
        • Needle and thread
        • Zippers (optional)
      • Method Two
        • A good pair of black pants. Ideally they should have slightly tapered legs. Make sure all the hardware (zipper and any rivets) is silver tone. Brass hardware will look totally out of place unless you use brass d-rings, etc. for everything else. If you can find a pair of black pants, not jeans, that have lots of rivets on them, that's all the better. Lots of pockets won't hurt either.
        • Black 1–1.5 inch (2.5–3.8 cm) webbing.
        • D-rings
        • Clasps
        • Needle and thread
        • Zippers (optional)

      About This Article

      Thanks to all authors for creating a page that has been read 101,851 times.

      Did this article help you?

      Advertisement