How to Install Landscape Timbers

Co-authored by Nihal Shetty Reviewed by Ben Barkan

Last Updated: November 25, 2024 Fact Checked

Want to liven up your garden with attractive and hardy landscape timber edging, but not sure where to begin? We’re here to help. Landscape timber is a great choice for a garden—its natural look is more attractive than steel, and it’s much more durable than plastic. Even better, it’s relatively simple to install. We’ll walk you through creating edging on a flat surface or on a slope: read on for our comprehensive guide on how to install landscape timbers.

1

Mark where your lanscape timbers will go.

Download Article

Set up mason lines to mark the locations of your landscape timbers. For a simple garden edge with a rectangular design, set up stakes at all 4 corners of your garden, and pull a mason line taut between each stake. If your planned garden is large enough that it’s difficult to keep a single line taut between two stakes, add an additional stake midway along your garden’s length or width. ^{[1]
X
Research source}
- If you don’t have a mason line, any other kind of string can work just as well.
- For ease of access, try not to have your timbers set at a width of more than 4 feet (1.2) meters from each other if you’re planning on creating a garden. ^{[2]
  X
  Research source}
- Although the length of the rectangle can be as long as you’d like, if the rectangle is too long, it’ll be difficult to reach your plants without stepping in your garden. ^{[3]
  X
  Research source}

2

Create trenches for your timbers.

Download Article

Dig trenches 3 inches (7.5 cm) deep along the mason lines. For tough turf, use a sharp spade . ^{[4]
X
Research source} These trenches will need to be wide enough to accommodate the size of your timber—usually 4 to 6 inches (10 to 15 cm) across. Remove as much organic matter, like roots or other plant residue, as you can. ^{[5]
X
Research source}
- If you’re working on a shallow slope (under 10 degrees), dig approximately 8 inches (20 cm) into the ground from the higher end of the slope. For steeper slopes, dig 12 inches (30.5 cm) into the ground. ^{[6]
  X
  Research source}

3

Even out the bottom of the trenches.

Download Article

Tamp down the ground to create a level surface. Run a level along the bottom of your trenches, removing or adding dirt as needed to create a level surface. With your hands or the back of your spade, tamp down the soil at the bottom of the trenches. ^{[7]
X
Research source}
- To add longevity to your timbers, add a layer of sand or gravel about an inch (2.5 cm) thick to the bottom of your trenches. ^{[8]
  X
  Research source}

4

Add landscape fabric (optional).

Download Article

Install landscape fabric if you want to keep out weeds. To do this, roll landscape fabric over the trenches, then drive it into the ground with small stakes and a hammer. Trim any extra fabric that hangs out over the edges. ^{[9]
X
Research source}
- This step is optional—if you aren’t worried about weeds in or around your trenches, it’s okay to skip this step.

5

Cut your timber to fit the trenches.

Download Article

Measure the length of each trench, and use this information to decide how many pieces of timber you’ll need. If you need a shorter piece of timber at the ends of each trench in order to match its length, mark the length of timber you need on a longer piece, then cut it . A circular saw works great for this, but a hand saw can also do the trick. ^{[10]
X
Research source}

6

Place your timber into the trenches.

Download Article

Line up the pieces of timber so that they’re a snug fit in the trenches. Use a level after placing each log so that you can be sure they’re level against the ground. If a piece isn’t flat against the ground of the trench, add or remove some soil from underneath it. ^{[11]
X
Research source}
- To make sure your timber edging lasts for a long time, use rot-resistant wood. Cypress, cedar, redwood, or pressure-treated wood can last beyond 7 years, while less durable options might need to be replaced earlier. ^{[12]
  X
  Research source}

7

Build your second layer of timber (optional).

Download Article

Place a second layer of timber on top of your first layer. Be sure that the layers of timber line up smoothly. If you’re having trouble making sure the second layer is level, place wood shims between the levels. ^{[13]
X
Research source}
- This step is only necessary if you want a taller garden edging. If you’re satisfied with the height of a single layer of timber, there’s no need to install a second.

8

Drill holes into your timber.

Download Article

Drill 2 holes on each log, 2 inches (5 cm) from each end. Pre-drill your wood with a power drill. Use a drill bit that is slightly smaller than the size of the rebar stakes that you’ll eventually be placing into it. By doing so, you can prevent your wood from becoming damaged. ^{[14]
X
Research source}
- If you have 2 or more layers of timber, drill through all of them at the same locations.

9

Secure the timber to the ground.

Download Article

Place the end of a rebar stake into the hole that you pre-drilled. Then, drive it through the wood and into the ground with a hammer. Use a hammer to push the rebar stakes through the timber, ideally using rods or rebar stakes long enough to be driven 2 feet (0.6 meters) into the ground. ^{[15]
X
Research source}

10

Clean up the area around the edging.

Download Article

For any areas near the timber that aren’t level with the ground around it, add dirt or soil. Tamp down any gaps that you’ve filled with soil. This will keep your timber even more secure and create an attractive garden edge. ^{[16]
X
Research source}

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Even pressure-treated wood has a much shorter lifespan than other materials because of its contact with soil. If you want a more permanent solution, consider using stone or metal. Pressure-treated wood in contact with wet soil can last 5 to 15+ years (or less) depending on the site conditions and wood quality.

Thanks
Helpful 0 Not Helpful 0

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

Log in

How to Install Landscape Timbers

Steps

Mark where your lanscape timbers will go.

Create trenches for your timbers.

Even out the bottom of the trenches.

Add landscape fabric (optional).

Cut your timber to fit the trenches.

Place your timber into the trenches.

Build your second layer of timber (optional).

Drill holes into your timber.

Secure the timber to the ground.

Clean up the area around the edging.

Expert Q&A

Video

Tips

Warnings

You Might Also Like

References

About This Article

Did this article help you?

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories