Download Article
Download Article
Installing a transfer switch refers to the process of adding the necessary trigger to change your energy to generator power in the event of an electrical outage. This task requires experience with electrical wiring. Follow these steps for how to install a transfer switch.
Steps
Download Article
-
Decide which home conveniences you'd like to be generator accessible. [1] X Research source- This usually includes the refrigerator, stove and other essential appliances.
-
Access your fuse box and calculate the amount of power that will be demanded of the generator to run each of these devices separately.Advertisement -
Confirm that the amperage of needed power does not exceed the generator's capacity.- The combined amperage may exceed the generator's capacity as long as the instruments aren't running simultaneously.
-
Assign each appliance a number which coincides with its circuit and label this in the circuit breaker of the switch.- The sizes of the assigned breakers must be equal in both the transfer switch and the home's load center.
-
Cut the main power supply to the circuit breaker. [2] X Research source -
Take the cover off of the circuit breaker. -
Remove the cover of the transfer switch.- The transfer switch is the device that disconnects the supply power from the local utility company and transfers the supply line to the emergency subpanel.
- Failure to install the transfer switch can result in combining voltages and damaging every electrical device in the house.
- The size of the transfer switch should be according to the power requirements of the sub panel.
-
Trim the unit's insulating tube, which will cover the wires, to a workable length using a utility knife. -
Attach the connectors to the wires using PVC cement. -
Use the transfer switch's wiring harness to connect the unit to the circuit breaker.- The wires should be drawn through 1 of 3 knockouts located on the underside of the switch. They should join the circuit breaker through a knockout found at the bottom of the box.
-
Lift the transfer switch up to the wall where it is to be installed and label the placement of the mounting screws. [3] X Research source- The transfer switch should be placed roughly 1 1/2 feet (45.72 cm) away from the midpoint of the main circuit breaker.
-
Affix the transfer switch to the wall, using mounting screws. [4] X Research source -
Pull the bundle of wires through the insulating tube. -
Trim 5/8 inch (1.59 cm) from the covering of each individual wire. -
Join the wires to the transfer switch referring to the labels created previously. -
Label each wire according to the appliance it supplies. -
Attach the miscellaneous black wires to the Utility 2-pole breaker in the transfer switch. -
Join the white wire to the neutral area located in the middle of the transfer switch. [5] X Research source -
Join the green wire to the grounding bar on the left side of the lower portion of the switch. [6] X Research source -
Put the cover back on the transfer switch. -
Confirm that the power supply is cut off at the main load center. -
Detach the assigned wires for each appliance from the circuit breaker box. [7] X Research source -
Trim 5/8 inch (1.59 cm) from the covering of each individual wire. -
Attach to the transfer switch using wire connectors and again referring to the labels. -
Join the miscellaneous black wires to the new 2-pole breaker. -
Detach the 2 individual pole breakers from where each assigned appliance wire was removed. -
Attach the white wire to the neutral bar. -
Join the green wire to the ground bar. [8] X Research source- If a ground bar is not present, join the green wire to the neutral bar.
-
Put the cover back on the main circuit breaker, and restore the power supply. -
Convert to generator power and return to utility power as per manufacturer's instructions.
Advertisement
Community Q&A
Search
-
QuestionThere are two black wires on some of the breakers, so how do I find out which is the positive and which is the negative? My transfer switch kit has red and black wires.NschmalCommunity AnswerIf this is a standard circuit breaker, there is no possibility of it having more than one wire of different definitions (any wire directly attached to a circuit breaker terminal is considered "hot"). A single-pole breaker will have one wire, a double-pole breaker is actually two breakers ganged together and will have two wires (one on each terminal). It's possible a double-pole breaker could have two wires of different colors, but they are still "hot" wires at 120 volts each. It's also possible that a single-pole breaker will have two wires in its one terminal - which means someone wired two different circuits to the same breaker.
-
QuestionCan I wire from an outlet directly to a circuit on the transfer switch? This is a hunting cabin and there is no fuse box currently.Community AnswerI don't know where you are, but in Ontario, Canada, not having a fuse panel or circuit breaker panel wouldn't be allowed. So here, an outlet cannot be attached to a transfer switch.
-
QuestionCould I hook up more than one wire on a transfer switch pole breaker?Community AnswerI live in Ontario, Canada. Here, you are only allowed one hot wire attached to the screw on a circuit breaker. You can run that one hot wire to a utility box and then make a connection that goes in two directions.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Always be sure to follow the manufacturer's instructions for tips for successful installation.Thanks
- The wires referred to in these instructions may differ in various transfer switch models.Thanks
- You may need to refer to building codes regarding the wiring specifications in your home.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
References
- ↑ https://electrical-engineering-portal.com/install-manual-transfer-switch
- ↑ https://electrical-engineering-portal.com/install-manual-transfer-switch
- ↑ https://www.northerntool.com/images/downloads/manuals/37850.pdf
- ↑ https://www.northerntool.com/images/downloads/manuals/37850.pdf
- ↑ https://www.electricgeneratorsdirect.com/manuals/rts_inst_man_2013.pdf
- ↑ https://www.diy-experts.net/easily-wire-transfer-switch-home/
- ↑ https://www.thisoldhouse.com/electrical/21016077/how-to-install-a-manual-transfer-switch-for-a-portable-generator
- ↑ https://www.diy-experts.net/easily-wire-transfer-switch-home/
About This Article
Thanks to all authors for creating a page that has been read 208,430 times.
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
