Download Article
Download Article
Impact smoke bombs are no joke. You should only handle them if you’re prepared to handle hazardous materials like black powder. For good fun and mischief, these will work in a similar way they do in the movies. There are different degrees of impact smoke bombs, so pick the bomb that's on your comfort level.
Steps
-
Gather the supplies. This filling can also be used as a standard smoke bomb by attaching a fuse. You’ll need a digital scale, KNO3 (potassium nitrate), powdered sugar, gloves, popsicle sticks or other stirring sticks, and a durable beaker. [1] X Research source- You’ll also need something to mold the liquified powders like a cardboard tube from a roll of paper towels.
- KNO3 can be found at larger hardware stores. If you’re having trouble you could also look at hobbyist shops or online. [2] X Research source
- The best gloves for this type of project would be rubber gloves.
- Wear protective eyewear and cover up your skin. These precautions are most important when you heat up the chemicals. Wear thick rubber gloves as well.
- You’ll also need the following supplies for the casing: paper toy caps, an exacto knife, tape, and black powder. Paper caps are the ammo used for toy cap guns.
- Black powder or gunpowder can be found at most sporting stores that sell guns. If you’re having trouble, look online. [3] X Research source
-
Measure out the powders. Use 70 grams (2.5 oz) of KNO3 and 30 grams of sugar. After weighing the powders dump them into the beaker and mix well. [4] X Research sourceAdvertisement -
Heat the mixture. Use a hotplate on medium low heat. Wear your gloves and stir frequently to avoid the compound from burning. Continue heating and stirring until the mixture liquefies and turns a tan brown color.- Beware of burning! If you are not careful the mixture could burn and go up in smoke.
-
Transfer to a casing. Transfer the liquefied mixture into the casing of your choice. Use something small so you can use the smoke bombs on the fly. The best type of case is something you can easily remove once the mixture has set, like a quarter of a cardboard toilet roll. You could also use a film cartridge, like the type you send into a photo center. -
Allow the mixture to harden. Give the mixture a few hours to settle. If you are feeling extra cautious, place the container into the fridge or freezer. This mix should take a little over an hour to cool in your freezer. -
Layer the caps. Place a small piece of tape on the edge of the cap and attach it to the top of the KNO3 blob. Then wrap the outside of the hardened mixture with the caps. Seal the caps together with tape once the surface is fully covered. -
Prepare the black powder. Cut two strips of tape slightly larger than the KNO3. Lie one strip perpendicularly over the first piece of tape creating a cross. Do this with the adhesive sides facing up. Shake the black powder over the tape cross.- Try to leave the outer edge of the tape clear.
-
Wrap the tape. Now that you have prepared the tape cross with black powder, it's time to finish the job. Take the KNO3 coated in toy caps and wrap it in the cross. The cross should fit onto the bomb in an easy fashion. Once you smooth out all the air bubbles, you’re all finished.- Throw the smoke bomb outside, using force, onto a hard surface like cement.
Advertisement
-
Gather the supplies. For this you’ll need a loose case, which you can make out of smooth paper or something fragile, like tissue paper. For the filling, you’ll need snappers (or “pop” rocks) and magnesium powder.- You can find magnesium powder at some hobby shops and online. Be sure you stay away from magnesium citrate, which is a health supplement.
-
Combine the materials. On a sheet of paper combine the snappers with the magnesium. For a decent smoke bomb you’ll need three to four snappers and a teaspoon of magnesium powder. -
Wrap the materials. Finish up the process by wrapping the two ingredients in the casing of your choice. You can simply use tissue paper if you can’t find anything in the house. Once cased, seal the mixture so that it is tight. Once you’re done throw it on a hard surface and you should see a flash, bang and smoke!- You can use tape or glue to seal the smoke bomb.
Advertisement
Community Q&A
Search
-
QuestionCan I use powder from inside fireworks instead of magnesium?Community Answerif you are a pyrotechnic chemist, and you know exactly what chemicals are used in said fireworks, then it might be possible. However, this would be INCREDIBLY dangerous for even a trained professional. in fact, even the smoke bomb designs shown here are ridiculously dangerous if you don't know what you are doing. In short, no, don't do it.
-
QuestionIs there a way to make the smoke bigger without the black powder?Community AnswerYou can do that by using more magnesium and snappers.
-
QuestionWhat are snappers? Where can I purchase snappers?Community AnswerSnappers are small "fireworks" that when you throw them hard, they make a "pop." You can find them online or in stores that sell fireworks.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Warnings
- Always wear safety goggle and do the experiment outside.Thanks
- Never throw it at any living things and always away from homes.Thanks
Advertisement
References
- ↑ https://io9.gizmodo.com/how-to-make-a-smoke-bomb-5879485
- ↑ https://www.thoughtco.com/where-to-buy-saltpeter-or-potassium-nitrate-3976011
- ↑ https://www.wideopenspaces.com/black-powder-101-everything-you-need-to-know-to-get-started/
- ↑ http://www.dynamicscience.com.au/tester/solutions1/chemistry/chemicaldemos/sugarkno3.htm
About This Article
Article Summary
X
To make a ninja impact smoke bomb, add KNO3 and powdered sugar to a beaker and mix them well. Next, use a hotplate to heat the mixture over medium-low heat, stirring frequently until the mixture liquefies. Transfer the mixture into the casing of your choice and let it harden. Then, attach caps to the KNO3 blob with tape and seal the caps together. Apply black powder to sticky tape and wrap it around the caps, then test your smoke bomb outside. If you want to learn how to use snappers to make a smoke bomb, keep reading the article!
Did this summary help you?
Thanks to all authors for creating a page that has been read 509,787 times.
Reader Success Stories
- "I liked the tips and how awesome it is making and owning a smoke bomb."
Advertisement
81%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"I liked the tips and how awesome it is making and owning a smoke bomb."
"I think this may be the best one I've tried yet! Thanks!"
"The easy access to supplies made it very easy to make."
"I was confused, but this explains it better."
