Download Article
Download Article
Laminate flooring is a relatively cheap and easy flooring to install yourself. When you install laminate flooring it's important to measure before making your order, measure for level so that the finished flooring is level, and measure your pieces as you install them for proper fit. With some attention to detail when it comes to measurements, your installation process will go more smoothly and your finished product will look like it was installed by a professional.
Steps
-
Measure the length of each wall in the room. Use a tape measure and have someone help you, so you can get an accurate measurement of each wall. Make sure that both you and your helper are holding the tape measure at the bottom of the wall, so that you get a true measurement of the length at floor level. [1] X Research source
- If the room is square or rectangular you only need to measure 2 of the walls. They should be walls that are touching at 1 corner, so that you know the length and width of the room.
- If you have an unusually shaped room, such as one with more than 4 sides, it's important to measure every wall.
-
Calculate the square footage of the room. Once you have the wall lengths, you can calculate the total floor space in a room. If the room is square or rectangular, you can simply calculate the square footage by multiplying the length by the width of the room. [2] X Research sourceAdvertisement
-
Divide the room up into square areas to get the square footage of an abnormally shaped room. You will need to mentally (or with a drawing) divide the space into square or rectangle portions. Then, you can figure out the square footage of each section and add them together at the end to get the total square footage.
- For example, if you have an "L" shaped room, divide it into 2 rectangular areas, calculate the square footage of both areas, and then add the square footage together.
-
Calculate how much flooring to order based on the square footage. Once you pick a specific laminate you want to use, look at its directions for instructions about how much to order based on the square footage of your room. Follow the manufacturer's directions, which typically has you order a bit more than you will need in case of mistakes during installation.
- Typically, you want to order about 15% more laminate than your square footage would suggest accounting for cuts and mistakes. To calculate this, multiply the square footage by .15. Then add the total to the square footage. [3] X Research source
Advertisement
-
Measure the levelness of the floor before installation. It is important to install laminate on a level surface so that the finished floor is level and doesn't have peaks and valleys. Get a long carpenter's level and place it in various locations all over the floor. When you find an area that is not level, make a mark on the ground. This will allow you to know where the floor needs to be leveled before installation. [4] X Research source
- If you don't have a level, you can run a board that you know is flat over the surface of the floor. If there are gaps in the middle of the board, you know that area is lower than the surrounding areas. [5] X Research source
-
Level the floor, if necessary. If you find that your floor is indeed off of level, you need to fix that. Purchase a leveling compound that is compatible with the flooring that will be under the laminate and the laminate itself. Then apply as directed on the product's instructions. [6] X Research source
-
Take the length of the floor and divide it by the width of the laminate pieces. This will give you the number of pieces it will take to span your floor. It's important to figure out how many pieces of flooring will fit in your room in order to ensure that when you get to the end, you won't be left with a very narrow space that is hard to fill with flooring. [7] X Research source
- If you come up with a number less than 2 left over, that means that you will need to use a very thin piece at the end. To avoid this and make installation easier, cut that much off of the width of the first board instead.
-
Measure for each piece as you go. It is likely that your first piece of laminate can go down uncut, but the second or third piece will. Measure the empty space, being sure to leave about 3 ⁄ 8 inch (0.95 cm) expansion space on all the edges of the floor. [8] X Research source
- The space you leave for expansion will be covered up when you put in baseboards or quarter-round molding around the edges of the floor.
-
Check your measurements before cutting. Measure twice and cut once is an old and well-known saying for a reason. Before you cut your laminate flooring pieces you should be certain about the length that you need. Measuring accurately will save you a ton of time and will cost you less money because you won't have as much wasted flooring. [9] X Research source
Advertisement
Expert Q&A
Search
-
QuestionHow much does it cost to install laminate flooring per square foot?Mitchell Newman is a Construction Professional based in Chicago, Illinois. He is the Principal at Habitar Design, an interior design firm that specializes in floor plans, kitchen and bath design, furniture layout, custom built-ins, custom and semi-custom cabinetry, staging, models, and facades. Habitar features a strong design-build capability, utilizing Mitchell’s sister company, Stratagem Construction. Mitchell is the General Contractor at Strategem, and has 20 years of experience in construction, interior design and real estate development. Mitchell’s two companies seamlessly combine interior design with construction, allowing him to design with synchony for the client. He received an M.D. from the University of Chicago Pritzker School of Medicine and a BS in Chemistry from the University of Illinois Urbana-Champaign.The most inexpensive laminate flooring can be as little as 80-90 cents a square foot, and it goes up to about $2-$3 per square foot. You'll also need a pad underneath the flooring, which can cost between 25-75 cents a square foot. Then, the exact cost of the installation will depend on the contractor, but that can be anywhere from $1.75-$4 a square foot.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
References
- ↑ https://www.familyhandyman.com/floor/wood-floor-installation/how-to-install-a-snap-together-wood-floor/view-all/
- ↑ https://www.familyhandyman.com/floor/wood-floor-installation/how-to-install-a-snap-together-wood-floor/view-all/
- ↑ https://www.thisoldhouse.com/flooring/21015018/all-about-engineered-wood-floors
- ↑ https://www.bobvila.com/articles/44271-how-to-install-laminate-flooring/
- ↑ https://www.familyhandyman.com/floor/wood-floor-installation/how-to-install-a-snap-together-wood-floor/view-all/
- ↑ https://www.familyhandyman.com/floor/wood-floor-installation/how-to-install-a-snap-together-wood-floor/view-all/
- ↑ https://www.familyhandyman.com/floor/wood-floor-installation/how-to-install-a-snap-together-wood-floor/view-all/
- ↑ https://www.bobvila.com/articles/44271-how-to-install-laminate-flooring/
- ↑ https://www.bobvila.com/articles/44271-how-to-install-laminate-flooring/
About This Article
Thanks to all authors for creating a page that has been read 35,906 times.
Advertisement