PDF download Download Article PDF download Download Article

Now that you’ve set your wick, mixed and poured your wax, it’s time to remove your new candle. It’s easy to get excited when you’re so close to seeing the result of your hard work. However, be patient and efficient in removing the candle from its mold. You’ll have to remove the mold sealer and extract the candle, as well as know how to remove stuck candles.

Part 1
Part 1 of 3:

Removing the Mold Sealer

PDF download Download Article
  1. Putty sealers typically get molded around the base of the mold to seal the hole. They’re usually pressed into a disk and stuck to the bottom of the mold. Removing this kind of sealer is as simple as peeling it off, much like sticky tack.
  2. Magnetic mold sealers are simple metal sheets that are magnetically charged. They snap onto the bottom of a mold to prevent wax from leaking out. Removing these is as simple as pulling them off.
    • If you’re using plastic or aluminium molds, you’re likely not using a magnetic mold sealer.
    Advertisement
  3. Watermark wikiHow to Remove a Candle from a Mold
    Rubber mold plugs are shaped somewhat like a spinning top; they have a large base and a tapered tip. Usually they just squeeze into the hole at the bottom of a candle mold. That means removing them is as simple as grabbing the base and pulling them out.
    • With rubber molds, the wick may be wrapped around a wick bar at the bottom of the mold. If so, you’ll need to unwrap the wick before you can remove the candle.
  4. Advertisement
Part 2
Part 2 of 3:

Extracting the Candle

PDF download Download Article
  1. If you try to remove the candle before the wax has set completely, the surface of the candle might tear and crumble. Leave the mold on a flat surface that won’t be damaged while the mold is still warm. It may take some time for the mold to cool; be patient. [1]
  2. Watermark wikiHow to Remove a Candle from a Mold
    Flip the mold upside down, so the opening faces downwards. Use your fingers to lightly tap on the bottom of the mold, which will shake the candle loose. Tap slowly and progressively, or the candle might slip out too quickly.
    • Don’t bang the mold against a counter or other hard surface, since this could damage the candle. [2]
  3. Watermark wikiHow to Remove a Candle from a Mold
    If tapping on the mold isn’t enough to dislodge the candle, you can gently tug on the couple of inches of wick poking out the top of the candle. Don’t use too much strength when pulling on the wick; you might break the string or cause it to slip out of the candle. [3]
  4. Advertisement
Part 3
Part 3 of 3:

Dealing with a Stuck Candle

PDF download Download Article
  1. Watermark wikiHow to Remove a Candle from a Mold
    Placing the mold in the refrigerator will speed up the cooling process, helping the wax set and separate from the mold. Flip the mold every 30 minutes; this will make sure the mold and wax cool evenly. Check the mold periodically; you’ll want to remove it from the fridge as soon as it’s cold to the touch.
    • Make sure you wait until the mold has cooled to room temperature before placing it in the fridge. If the temperature change is too drastic, the candle could crack. [4]
  2. If the candle’s especially difficult to dislodge, you can try putting the mold in the freezer. Take it out after five minutes and try to remove the candle. If it still won’t budge, leave it in the freezer for an additional five minutes. You don’t want to leave the mold in any longer than 10 minutes, since this will definitely cause the candle to crack. [5]
  3. Watermark wikiHow to Remove a Candle from a Mold
    Finally, if you’ve tried all of the above and can’t remove the candle, you might have to cut your losses. Place the mold in a metal dish filled with boiling water and wait for the candle to soften. After a few minutes, you should be able to retrieve the candle; use a pair of tongs or a wooden spoon to avoid burning yourself.
    • This process won’t save your candle, but you can at least melt down the wax for use in your next attempt.
  4. Advertisement

Community Q&A

Search
Add New Question
  • Question
    There is a small metal disc stuck in bottom of the glass which had a candle in it. How do I release the disc?
    Community Answer
    Pour a small amount of eucalyptus oil into the glass jar so it just covers the disk. Leave it overnight if you can wait that long otherwise after an hour or so you can try manually lifting it using a butter knife. You can also try freezing the glass overnight which should make the wax and disc easier to remove.
  • Question
    Why did my skull candle crack?
    Community Answer
    You were probably not careful enough. If you try again, handle it more gently next time.
  • Question
    I have a silicone unicorn mold, but every time I open the mold the wings break off of the candle. Do you have any suggestions for me?
    Community Answer
    Make sure you are using a hard wax for this and not a softer wax. The softer wax tends to break with ease.
See more answers
Ask a Question
      Advertisement

      Tips

      Tips from our Readers

      The advice in this section is based on the lived experiences of wikiHow readers like you. If you have a helpful tip you’d like to share on wikiHow, please submit it in the field below.
      • Spread oil (olive oil is best) around the inside of the mold and pour the wax in. Once wax is poured, store it in the refrigerator and keep it in there for a long time. Although wax cools really quickly, you should still chill it in the refrigerator for a long time.
      • To prevent a dip in your candle, heat the container you're pouring the wax into so it acclimates. It also helps to pour your wax in slowly.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      About This Article

      Thanks to all authors for creating a page that has been read 170,051 times.

      Did this article help you?

      Advertisement