How to Use a Plunge Router

PDF download Download Article
PDF download Download Article

One of the most versatile electric tools available to a woodworker is the router. The router comes in 2 forms, the fixed base and the plunge base. The router used most by the woodworker is the plunge base. It may seem more difficult to use at first, but you can learn how to use a plunge router by following the steps below.

Steps

PDF download Download Article
  1. You will note that it contains an electric motor mounted between two posts. The motor rests on top of springs and is attached to a flat base that guides the motor down at a 90 degree angle. [1]
    • The motor rises back into position when downward pressure is released, raising the router bit above the base.
    • Attached to a collet, the motor connects much like a hand drill chuck. It comes in 2 sizes, 1/4 inch and 1/2 inch (as well as 8 mm and 12 mm in metric sizes). This is where the router bit does the cutting.
  2. The bigger the motor, and consequently the collet, the bigger the router bit. As a result, the cut is deeper. [2]
    Advertisement
  3. Remember, a higher price does not necessarily mean a better tool. [3]
  4. These are often shop made or bought as add-on accessories.
    • The most common jig will be used for cutting dadoes. Dadoes are used in joining two pieces of wood at 90 degrees, such as adding a kitchen cabinet shelf to a side piece. This type of joint uses a straight cut router bit for dadoes.
    • Clamp the guide into place so that, when the router bit is plunged downward, the bit will line up with the dado joint you want to cut.
  5. [4]
  6. Pull the trigger and push downward while holding the router with both hands. This act will engage the bit with the wood.
  8. The router will retract into the base.
    • Install the desired router bit in the collet. Most profile-edge bits, like a round over or Roman Ogee bit, will have a sleeve bearing that will guide the bit along the edge of the work piece.
    • Set the depth gauge for the amount of bit you want to use.
  10. Firmly press downward, holding the handles while pulling the trigger. [5]
    • Push in against the edge engaging the bit while fully extended to the depth needed.
    13. Advertisement

Community Q&A

Search
Add New Question
  • Question
    How do I build a router table?
    Donagan
    Top Answerer
    Take a look here: TheBalance.com/free-router-table-plans-1357138.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 5 Helpful 8
  • Question
    How do I use an angle grinder as a wood saw?
    Donagan
    Top Answerer
    There's an old saying: use the right tool for the job. There are so many kinds of saws available, it's hard to imagine that you couldn't find a size and tooth pattern to fit the job at hand. A grinder will burn your wood and generally exasperate you unless there's very little wood to remove. In that case you might consider a file, a sander, or a chisel.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 0 Helpful 1
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Video

      Tips

      • A plunge router, like a fixed base router, can be used in a router table. However, it can be more difficult to adjust the height.
        Thanks
        Helpful 8 Not Helpful 1
      • Read the instruction manual thoroughly, with the router in hand. Go over the pieces and any accessories that came with it before trying to put it to use.
        Thanks
        Helpful 6 Not Helpful 6
      • Make multiple passes on deep cuts. Attempting to make one deep pass on a dadoes or rabbit joint will bog down the router. Other problems of uneven cuts and kick back will occur as well.
        Thanks
        Helpful 4 Not Helpful 6
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      Things You'll Need

      • Plunge router
      • Router bits
      • Guides or jigs with clamps
      • Dust mask
      • Safety glasses

      You Might Also Like

      How to
      Build a Router Table
      How to
      Use a Dremel Tool
      How to
      Plane Wood
      How to
      Use a Wood Lathe
      How to
      Use a Crimping Tool
      How to
      Use an Angle Grinder
      How to
      Adjust a Crimping Tool
      How to
      Sharpen Chisels
      How to
      Set Planer Blades
      How to
      Set Up a Lathe
      How to
      Use a Jigsaw
      How to
      Use a Deburring Tool
      Advertisement

      References

      1. ↑ https://www.youtube.com/watch?v=8Vl8Jbw3cSk
      2. ↑ https://www.youtube.com/watch?v=8Vl8Jbw3cSk
      3. ↑ https://www.wwgoa.com/article/router-basics-how-to-use-a-router/
      4. ↑ https://www.wwgoa.com/article/router-basics-how-to-use-a-router/
      5. ↑ https://www.youtube.com/watch?v=eOKco1aOygY
      6. http://www.popularmechanics.com/home/reviews/4301758?click=main_sr
      7. https://www.youtube.com/watch?v=rJGXqtOsB6A
      8. https://www.woodmagazine.com/woodworking-tips/techniques/routing/plunge-router?mode=step_by_step

      About This Article

      In other languages
      Thanks to all authors for creating a page that has been read 130,794 times.

      Did this article help you?

      Advertisement