Download Article
Download Article
A serger, or overlock sewing machine, gives garments and other sewn objects finished seams. When using one, you get many things done for you; a serger will secure seams with an overlock stitch to cover raw edges and cut excess fabric. The overlock stitch is ideal to use on knit fabrics since it has built-in stretch. The most important part of using a serger is threading the machine properly, since it has between three to five spools of thread.
Steps
-
Turn the machine off. A serger should be off when you thread it. Locate your sergers power button and switch it off. [1] X Research source -
Determine the correct threading order. Most sergers use four spools of thread: two for looping underneath the needles and two to use in the needles. The model you have will tell you the order in which you thread them. Look at the threading diagram on your machine. [2] X Research source- A 3-thread machine has an upper looper, lower looper and a single needle thread.
Advertisement -
Place a spool of thread on the upper looper. More than likely the upper looper will be on the right side of the machine. Set a spool of thread on the correct spindle for this.
-
Thread the upper looper. Pull the upper looper thread up so that it is just below the needles. Remove the faceplate on the machine's front and pull the thread through the metal loops underneath the plate. Your serger will most likely have a color-coded guide to help you thread the upper looper.
-
Thread the lower looper. Set the spool on the second spindle and bring the thread over the front of the machine. Use tweezers to help you get the thread through the tight spots on the machine.
-
Thread the needles. Set the threads on the spindles and bring them over the front of the machine. Put the thread through the needle or needles on the overlock sewing machine.
Advertisement
-
Turn on the serger. You will need to use your serger to adjust the tension, so switch the power button on.
-
Determine what stitch you want to use. A serger can do many things like create a rolled hem, finish raw knit edges and gather fabric. Look at your user manual to determine what stitch you need to use for your desired result. [3] X Research source
-
Adjust each spool’s tension dial. After you decide on what effect you want, your manual should tell you the required tension for each spool. Adjust each tension dial accordingly.
-
Run a practice stitch. You do not need fabric under the needles to test a serger stitch. Place your foot on the machine pedal and let the machine create looped thread.
-
Inspect the looped thread. You should have an idea of how your stitch should look by looking in your serger’s user manual. The loops and interlocking stitches should be even, without areas that are too even or too loose.
- If the stitches are loose, adjust the tension dials next to each spool of thread on the overlock sewing machine to make the thread tighter.
- If the fabric is puckered or bunched up, loosen the tension on the serger.
-
Practice on a scrap of fabric. Find a piece of scrap fabric to test your stitch. Continue to sew practice stitches until the stitches are even.
- Always do a practice stitch whenever you change your needle, thread, or any other part of the machine. That way, you can make sure that everything is in place and working properly.
Advertisement
-
Lift the presser foot and needles. Lift the presser foot lever up to lift the metal presser foot and turn the needle dial towards you to lift the needles.
-
Push your fabric under the needles and foot. Lift your practice string up and back while you slide your fabric under the presser foot and needles.
-
Lower the presser foot and needles. Lower the presser lever to lower the foot and turn the needle dial towards you to lower the needles.
-
Cut the fabric edge. A serger will finish seams and cut your fabric at the same time. Look at the seam allowance numbers to the right of the needle and push the fabric past the blade accordingly. This can be 1.5 to 2.5 cm depending on what seam allowance you used when measuring your fabric.
-
Sew and guide fabric under the needles. Use the foot pedal to control the speed when sewing. Don't push on the fabric too hard and remember to keep the fabric straight. The feet on the overlock sewing machine should help push the fabric through.
-
Create a tail of stitches. Continue sewing for a few stitches at the end of your seam to create a tail of stitches that you can tuck under and hand sew in place.
Advertisement
Community Q&A
Search
-
QuestionWhat do I do if I always have an extra thread when I pull the fabric out on a four thread overlock?Community AnswerYou shouldn't be pulling the fabric out. You should continue sewing past the end of the fabric for a few inches, then just cut the chain, not too close to the fabric if you need it neat. You can then tuck the chain underneath and stitch it, or unravel it and sew the ends in.
-
QuestionIs there a tool to change the needle?Community AnswerYour serger should have come with a little hex screwdriver. You need this to loosen and tighten the screw holding in the needle. On some models of machine, the cleaning brush has some holes in the handle, these are intended to be used as needle holders to facilitate inserting the needle.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Use long handled tweezers to thread a serger and reach into tight places.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Never start sewing with the needles in a raised position when you use a serger.Thanks
Advertisement
Things You'll Need
- Serger
- 4 spools of thread
- Tweezers
- Fabric
References
About This Article
Article Summary
X
To use a serger, start by making sure your machine is turned off, then following the threading diagram to thread the upper looper, the lower looper, and the needles. Next, turn your machine on, and adjust the tension dials for the type of stitch you want according to your machine’s manual. When you’re ready to finish your seams, lift the presser foot lever up, turn the needle dial toward you, and push your fabric under the needles and the foot. Then, lower the presser lever, turn the needle dial back, and begin sewing, using the foot pedal to control your speed. For tips on how to test the tension on your machine before you begin sewing, scroll down!
Did this summary help you?
Thanks to all authors for creating a page that has been read 116,731 times.
Advertisement
"Helped a lot, got one with no instructions."
"Great source for my project on the serger."
