Download Article
A guide to safely routing and connecting electrical wires to a contactor
Download Article
Many large pieces of equipment are powered directly from high voltage lines. These lines far exceed the 120 volts AC standard in most homes. 240 volts AC and 480 volts AC are commonly used for these large pieces of equipment, such as motors, industrial machines, and large household appliances like washers and dryers. These voltages must be electrically isolated from the standard 120 volts AC. Contactors are used to provide this isolation. Contactors use 120 volt standard power to energize a magnetic coil, which causes a set of internal contacts to close and provide higher power to the equipment. Use these tips to learn how to wire a contactor.
How to Do Contactor Wiring
- Look over the contactor manufacturer information to identify the input and output pins.
- Determine if the contactor has an auxiliary output contact.
- Strip the wires.
- Run all input and output wires to the contactor.
Steps
Download Article
-
Acquire the contactor. Make sure that the contacts of the contactor are rated in both voltage and current to handle the expected load that will be required by the equipment being powered. Contactors are available from building and construction supply stores, as well as some larger hardware stores. -
Study the contactor manufacturer information. The manufacturer information will identify the 2 input pins for 120 volts AC control. The may be 2 or more sets of output contacts identified. These contacts may be indicated on the label as normally open (NO) and normally closed (NC). These contacts also may be shown as a drawing of a line from 1 contact ending in a dot (the NC contact) and another line from another contact that is near the dot, but does not touch the dot (the NO contact.) [1] X Expert Source Ricardo Mitchell
Electrician, CN Coterie Expert Interview. 6 May 2020.Advertisement -
Check for an auxiliary output contact. Some contactors provide an auxiliary output contact as a signal to the isolated part of the circuit that the contactor has been energized. This auxiliary contact will not be rated at the higher voltage. Instead, it should be rated at 120 volts AC. -
Route the wires. Remove all power to the wires. Run all input and output wires to the contactor. These wires should be rated in the manufacturer information. Use wire strippers to cut excess length off of the ends of the wire, making sure that the wires are long enough to reach the intended contact. Wire strippers are available at hardware stores and electric supply stores. -
Strip the wires. Use the wire strippers to strip a half inch (13 mm) from the ends of each wire. If the wire is stranded, twist the exposed wire to ensure that no strands are left hanging. Stray strands may make unintended contact with a piece of the equipment and cause damage. -
Wire the inputs and the auxiliary contacts. Use a screwdriver to loosen the holding screws in the contact blocks for the wires. Insert the wires only so far that no insulation is pushed into the contact area of the block. Make sure that no stray strands are jutting out from the contact block. Tighten the screws on the contact blocks. -
Energize the contactor. Apply the control voltage to the input. Listen for the contactor to click as it engages. De-energize the contactor. -
Connect the outputs. Put the stripped end of each wire into the appropriate contact block after loosening the screw of the block. Make sure that no stray strands of wire are jutting from the contact blocks. Tighten down the screws of the contact blocks.
Advertisement
Expert Q&A
Search
-
QuestionMy contactor doesn't really match up with the illustrations? Will this still work?Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience.There are all different kinds of contactors out there, and they're all wired differently. Consult the diagram that came with your contactor and follow their instructions.
-
QuestionWhat are the letters on the conductor?Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience.Most conductors label the terminals with letters like L, N, E, A1, A2, L, and P. Those correspond with the letters on the diagram that came with your contactor. It should make it a lot easier to wire everything together.
-
QuestionWhat does 'loop' mean?Community AnswerA loop is a fastener consisting of a ring that protects the inside surface of a small hole.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Warnings
- All voltages used for a contactor, including the 120 volts AC control voltage, are potentially fatal. Make sure that all power is turned off before any work is done on a contactor.Thanks
Advertisement
Things You'll Need
- Contactor
- Wire strippers
- Screwdriver
- Wire
References
- ↑ Ricardo Mitchell. Electrician, CN Coterie. Expert Interview. 6 May 2020.
- https://www.allaboutcircuits.com/textbook/digital/chpt-5/contactors/
About This Article
Thanks to all authors for creating a page that has been read 521,394 times.
Reader Success Stories
- "This is a clear and easy to understand article with step-by-step instructions. Thank you."
Advertisement
"This is a clear and easy to understand article with step-by-step instructions. Thank you."
