Download Article
Download Article
Applying wood veneer was once rumored to be a difficult task, reserved mainly for seasoned professionals. These days, since tools and supplies are readily available and many of the methods are so simple, even a novice woodworker can easily master the process. There are as many techniques for application as there are varieties of veneer, but contact cement is commonly regarded as the most practical method. It is also among the most enduring applications. Here are some guidelines to get you started as your learn how to apply wood veneer.
Steps
Download Article
-
Cut the substrate (the material that the veneer is actually applied to) to the exact finish size. This way, you can cut just the excess veneer with a razor knife and avoid damaging the finished product by using a table saw.
-
Select the most appealing section of the veneer pattern, which will be visible in the finished piece, keeping in mind that any excess will be trimmed. [1] X Research source
- One effective way to isolate your preferred section is to make a cardboard template. This will need to be cut to the identical size of the substrate panel by laying the substrate over the cardboard, marking the edges and then cutting the cardboard.
Advertisement -
Place your template over the desired section of veneer and cut out that portion, leaving approximately one-half inch, or 1.27 centimeters (0.5 in), of excess on each side.
-
Center the selected pattern section over the substrate panel and apply the contact cement, following the manufacturer's instructions, to both the veneer and the substrate. Allow it to set. [2] X Research source
- Be sure to mix the adhesive thoroughly before applying it. This will maximize its effectiveness.
-
Use extreme caution when positioning the two elements for adherence. Since contact cement is so slip-resistant, they must be perfectly aligned on the first try. [3] X Research source
-
Using maximum pressure, roll the veneer smooth by starting in the center and working out toward the edges using a veneer roller. [4] X Research source
-
Still using maximum pressure, smooth the surface with a smoothing blade to verify that the veneer is completely adhered. [5] X Research source
-
Turn your piece upside down and use a razor knife to trim the excess veneer, using the edges of the substrate as your guide. [6] X Research source
- Run your hand over the area to be sure that the area is entirely smooth. If you do encounter any bubbles, repeat the two previous steps.
- You can ensure a cleaner cut by scoring the surface first to determine the cut
-
Allow ample time for curing and drying before finishing the piece.
Advertisement
Community Q&A
Search
-
QuestionWhat other tool can I use if I don't have a razor knife?Community AnswerA special guillotine for veneer. But those are hard to find. A razor knife is best for home use.
-
QuestionHow do I bend veneer?Community AnswerPut it in boiling water for about 20 minutes. That will allow you to bend it more. Bend the veneer to the position you want and allow it to dry like that. (Wait until it's very dry before gluing it.)
-
QuestionI am putting veneer over veneer. How do I begin prepping?Ashton GilmoreCommunity AnswerAs long as the underlying veneer has no coating and is adhered securely to the base piece, I would simply sand the underlying veneer to rough it up.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- One way to ensure the proper positioning is to cut a piece of waxed paper to the size of the veneer, leaving some excess on one side and placing it between the substrate and the veneer. This allows you to position both pieces to your satisfaction before sliding the waxed paper out to initiate adherence.Thanks
- If, after smoothing and re-rolling the veneer, you are still encountering bubbles, you can release any remaining trapped air by making small, subtle slits in the veneer. Make sure to go in the direction of the grain.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
Warnings
- Contact cement is a great application method because the cement is absolutely permanent. The drawback of this is that you need to be perfectly accurate when aligning the veneer and substrate.Thanks
Advertisement
References
- ↑ https://www.youtube.com/watch?v=23UAlN3KfTk
- ↑ https://www.youtube.com/watch?v=23UAlN3KfTk
- ↑ https://www.youtube.com/watch?v=BeFzAPik_68
- ↑ https://www.popularwoodworking.com/techniques/veneer-techniques/how-to-apply-wood-veneer-with-backing/
- ↑ https://www.youtube.com/watch?v=BeFzAPik_68
- ↑ https://www.handymantips.org/how-to-apply-wood-veneer/
- https://www.finewoodworking.com/2015/05/27/introduction-to-wood-veneering
About This Article
Thanks to all authors for creating a page that has been read 126,123 times.
Reader Success Stories
- "The step-by-step method, enhanced by large, clear illustrations explaining each DIY procedure, is of the best I have ever seen. Training centers and technical schools could benefit substantially from posters of this type, as would DIY retailers." ..." more
Advertisement
"The step-by-step method, enhanced by large, clear illustrations explaining each DIY procedure, is of the best I have ever seen. Training centers and technical schools could benefit substantially from posters of this type, as would DIY retailers."
..."
more
"I would not normally use contact cement on timber, and was quite surprised that you recommend contact. But after doing the job the way that you recommend and leaving the timber in the room for 48 hrs before attempting the job was a good point."
..."
more
"It's that easy! I've been planning to refit my Nelson 34 boat, built in 1968, with veneers to match the modern teak finish. That's after I strip back the bulkheads that are yellowed by UV light varnish. I'll definitely be taking it on now."
..."
more
"The simple instructions with detailed pictures really helped. Just reading with no illustration makes a project like this confusing, but this tutorial made it seem simple."
..."
more
"I'm a complete novice with veneer, so this article alerted me to the need for the roller and smoothing blade which, upon reflection, makes complete sense."
..."
more
