How to Build a Closet

Reviewed by Barry Zakar

Last Updated: November 3, 2022

A closet is often the most under appreciated room in a house - until you need one. Then the storage space it represents becomes a valuable asset. It does not take a professional to build a closet only a willingness to set aside some time and have access to both hand tools and basic power tools.

Steps

Download Article

This can be the most difficult part of the process. The most logical place would be an alcove, the end of a hallway or on a wall without windows or doors to work around.
Whether it is a wall or walk-in closet will depend on the amount of room available to you.

Advertisement
Be careful not to break the trim, since you will want to reuse it.
4
Install the framing, beginning with the base and top plate. Attach the base with deck screws to the floor and the top plate to the ceiling. Use 4-inch (10.2 cm) toggle bolts and construction adhesive.
- Nail or screw the end studs to side walls and to the top and base plates and rough in the door opening by nailing the studs to the top and bottom plates. Studs traditionally are on 16 inches (40.8 cm) spacing. Just use the spacing you have if width of your wall is greater than 16 inches (40.8 cm) but less than 24 inches (61.2 cm). Split the difference for better support of the sheathing if the width is greater than 24 inches (61.2 cm).
- Rough in the door framing. This will include trimmer studs on each side of the door. Dimensions are normally 6 feet (1.8 m), 10.5 inches (1.83 m x 26.7 cm) tall attached to the wall studs and a doubled 2 x 4-foot (5.1 X 10.2 cm) door header nailed to the door trimmer with the end nailed to the wall stud.
- Place short studs (called cripples) between the door header and ceiling plate. This will normally be centered on 16 inches (40.8 cm). The framing is complete.
5
Hang .5-inch (1.27 cm) sheetrock or sheathing on the walls. Both sides of the framing use sheetrock screws. Cut sheetrock to size using a utility knife and a straight edge as a guide. Run the edge of sheathing to the roughed-in door openings.
- Score the sheetrock with a utility knife. Begin breaking the sheetrock off with hand pressure and then with a straight edge (along the back side of the sheetrock). The sheetrock should snap off in one piece if it is scored deep enough.
6
Position the doors in the closet. How to do this will depend on the type of doors chosen.
- Insert the door into your rough opening if you are using a traditional prehung door (as for a walk-in-closet). Then, with a level, plumb the door using shims to keep it aligned. Install the trim supplied by the manufacturer around the door.
- The use of a bi-fold door requires that you first trim out the door opening. Use trim similar to the floor trim you salvaged or that matches the trim in the room. Hang the door in place and adjust to fit, following manufacturer's instructions. ^{[1]
  X
  Research source}
- Install the accessories, however elaborate or simple, that fit your needs.

Community Q&A

Search

Add New Question

Question

How do I install sliding doors?

Community Answer

Install according to manufacturer's instructions. They're usually easy to follow.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 10 Helpful 6
Question

How do I expand my closet space?

Community Answer

Move the hanging rod up and then install another hanging rod below your clothes hanging on the top rod. You can also add shelves a few inches above the hanging rods to accommodate non-hanging items. Plastic totes are very good for placing on the floor. There are even shallow closet shelves that screw to the back or even front of the door.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 2
Question

How far between studs?

Community Answer

16" on-center or left edge to left edge. This translates to 14 1/2" actually between studs. However, if you know exactly where hanging rods will be going for 1 or 2-tier hanging then you may want a double stud there or blocking in between studs.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 4 Helpful 5

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Prehung doors are the easiest to install in that they come with all of the hardware installed and with the trim to go around the door. These are available at most home improvement stores. ^{[2]
X
Research source}

Thanks
Helpful 0 Not Helpful 1
A good way to see how the space for the closet and the room fit together is to chalk out the closet walls, then place any needed furniture to see if it works.

Thanks
Helpful 0 Not Helpful 0
Check to see the width and height requirements for the rough opening for the door you've chosen (when using prehung or bifold doors).

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

You will probably not need a building permit to install a closet. However, if you are adding electrical lighting or plugs, you may need an electrical permit which requires a licensed electrician to do the work. Check your local building codes.

Thanks
Helpful 0 Not Helpful 1
Make sure that there are no existing electrical lines or plumbing in the way before installing or drilling into any existing walls. ^{[3]
X
Research source}

Thanks
Helpful 0 Not Helpful 0

Things You'll Need

Framing hammer
Pry bar
Crosscut hand saw
Electrical miter saw
Power drill -- electrical or battery powered.
Utility knife
4 foot (1.22 m) level
4 inch (10.2 cm) x 1/4 inch (.5 cm) toggle bolts
3 inch (7.6 cm) deck screws
16 P framing nails
Construction adhesive
2 x 4 inch x 8 foot (2.4 m) (5.1 x 10.2 cm x 2.44 m) Douglas fir or pine for framing
.5 inch x 8 foot (2.4 m) (1.3 cm x 2.44 m) sheetrock
1.5 inch (3.8 cm) sheetrock screws or nails
Tape and embedment compound
3 inch (7.62 cm) putty knife

You Might Also Like

[1]

[2]

[3]

Log in

How to Build a Closet

Steps

Community Q&A

Tips

Warnings

Things You'll Need

You Might Also Like

References

About This Article

Reader Success Stories

Did this article help you?

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories