How to Build a Crank and Slider Mechanism

Last Updated: September 12, 2022 References

A crank and slider is a useful mechanism if you need to convert rotational motion into reciprocating linear motion. To build one, you'll ned a crank shaft, a linkage or connecting rod, and a slider. We'll show you how to build a simple, working model at home out of household materials, wood, or metal. ^{[1]
X
Research source}

Steps

Download Article

This example will use cardboard and wire, since just about anybody can readily obtain and cut them, but a sturdier or more attractive model could use balsa wood, Popsicle sticks, wood, stiff craft foam, metal, or found materials such as a container lid. Choose materials according to what you can find and whether you can work with them easily. ^{[2]
X
Research source}
The base simply supports the other mechanism parts and provides pivot points for the rotating members. In this cardboard model, a large sheet of cardboard cut from the side of a cereal box will serve as the base. ^{[3]
X
Research source}

Advertisement
The crank needs two pivot points. They may be on a circular cutout as shown here, or they may be on either end of a short rectangular piece. If you'd like a circle, use a compass or trace around a circular object of a suitable size, such as a can or glass. Make a hole in the center of the crank and make another near the edge of the circle. For a linear crank, make holes near each end. Don't put any holes too close to the edge.
Make it about twice as long as the distance between the two holes. Make holes near either end of the shaft.
This can be a simple rectangle of whatever material you are using. If you will place the slider into a tube, such as a pipe, you may prefer a cylindrical object, such as a cork or a piece of dowel or rod. Place a hole in one end of the slider.
For a two-dimensional cardboard model, you can use rectangles folded and glued to your base. Make these retainers two times as long as the crank, plus the length of the slider.
This model uses craft wire and buttons, but any assemblage that will fit freely through the holes and hold the pieces together while allowing them to rotate against each other will do.
If you're making a two-dimensional model on a base of wood or cardboard, place the shaft on top of the crank. ^{[4]
X
Research source}
In a two-dimensional model, place the slider under the shaft.
Arrange the retainers on either side of it so that it has a path to move and fasten them down. Glue or even staples will do for paper.

Community Q&A

Search

Add New Question

Question

What is the use of rope in a crank and slider mechanism?

Community Answer

THe use of the rope to pull the slider, so it pulls something else by turning the crank.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 10 Helpful 6
Question

What pivot is this talking about?

Community Answer

A slider pivot.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 8 Helpful 6

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Because the crank end follows a circular path, the motion of the slider will follow a sinusoidal pattern. Put another way, the location of the slider follows the sine of the angle of the crank. This also means that for a constant rotational speed of the crank, the velocity of the slider will be greatest in the middle of its travel and least at the ends of its travel. ^{[5]
X
Research source}

Thanks
Helpful 1 Not Helpful 0
Use a ruler to cut on straight lines, especially for the slider.

Thanks
Helpful 1 Not Helpful 0
Make the pieces fairly broad, especially if you are working in a delicate material such as cardboard or balsa wood. It will help keep them from bending around too much or folding instead of turning.

Thanks
Helpful 1 Not Helpful 0

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Wear safety glasses if you will be operating a drill or using a craft knife.

Thanks
Helpful 9 Not Helpful 1
If your materials are more heavier rigid than cardboard, be careful of pinching your fingers between moving parts.

Thanks
Helpful 5 Not Helpful 7
Metals can have sharp edges, especially when cut. Use appropriate caution.

Thanks
Helpful 1 Not Helpful 1

Things You'll Need

Materials of your choice: wood, metal, stiff cardboard, craft foam, or found objects.
A means of cutting holes in these materials.
A means of fastening the materials as a pivot: wire, brads, screws, etc.
Retainers for the slider: blocks or folded, fixed walls.

You Might Also Like

[1]

[2]

[3]

[4]

[5]

Log in

How to Build a Crank and Slider Mechanism

Steps

Community Q&A

Tips

Warnings

Things You'll Need

You Might Also Like

References

About This Article

Did this article help you?

About This Article

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories