Download Article
Learn to effortlessly swap a keg to keep the party going
Download Article
Changing a keg of beer is a simple procedure but must be done systematically to reduce waste and ensure peak freshness and flavor. If you want to learn how to change a keg, follow these guidelines.
How do you change a keg?
- Make sure the keg is empty by checking for frothy beer.
- Turn off the CO2 line, if the keg has one.
- Raise the coupler handle at the base of the tap and remove the coupler.
- Take the plastic cap off the new keg.
- Align the lugs on the base of the tab with the keg's well slots.
- Tap the keg firmly with the coupler handle raised.
- Press the coupler handle down and turn on the CO2
Steps
-
Check to make sure your keg is empty. You'll know that your keg is empty if you open the faucet of the tap and either very frothy beer comes out or none does. -
Look to see if your keg has a CO2 line. Some kegs will have a CO2 tank that provides pressure inside the keg to help dispense beer. The gas also helps the beer hold its natural carbonation. If the system you're using has a CO2 line, turn it off.Advertisement -
Lift the coupler handle at the base of the tap where it joins the keg. Grasp the coupler and rotate it counter-clockwise until it won't move anymore, usually just a half-turn. [1] X Research source -
Pull the coupler off the empty keg. [2] X Research source -
Move the empty keg aside.- You can use Powdered Brewery Wash or PBW to clean kegs at home.
- Mix hot water and PBW in the keg.
- Scrub with a sponge if needed, or let it sit overnight and rinse the next day.
Advertisement
-
Put the fresh keg in a refrigeration unit or in a tub of ice. -
Remove the plastic cap from the top of the keg. The cap will show the brand of the beer and its freshness date. -
Ensure that the well of the keg is clean. -
Line up the lugs on the base of the tap with the slots in the well of the keg. [3] X Research source -
Keep the coupler handle raised and fit the tap firmly onto the keg. Twist the tap a half-turn, in a clockwise direction, until it is snug. [4] X Research source -
Press the coupler handle down to its locked position. -
Turn the CO2 canister back on. -
Open the faucet fully to expel excess foam that is often built up in freshly tapped kegs. -
Make sure the beer flows through the faucet and there are no obvious leaks. If the beer doesn't flow, repeat the process.
Advertisement
-
Check the gauge of the CO2 canister to make sure the cylinder is empty. The gauge should read 0. Other signs that you may need to replace your CO2 canister are that no beer flows from the faucet, or the beer is flat. -
Shut off the valve at the top of the canister by turning it clockwise until it won't go any further. -
Use a spanner, or specialized wrench, to slowly disconnect the reducing valve from the cylinder to let the remaining gas escape. This will reduce the pressure inside the valve. -
Set aside the empty canister. -
Install the new CO2 canister.- Remove the protective tape from the replacement canister's outlet valve.
- Connect the new cylinder, tightening it with the spanner. Be sure to install a new plastic washer each time you change your gas canister.
- Turn the valve back on, twisting it counter-clockwise. Turn it until the hissing from the canister stops and the knob won't turn any further.
- Make sure the gauge shows pressurization.
Advertisement
Community Q&A
Search
-
QuestionWhen I remove the coupler from the empty keg it sometimes loudly releases gas, even with the handle in the upright position. What am I doing wrong?Community AnswerYou have to lock the handle into the upright position. It should click and stop the gas. Turn off the gas from the pump would also be a good idea. If all else fails, its a faulty line and needs replacing.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- A CO2 cylinder will last for 7 to 10 kegs, depending on their size.Thanks
- If you're chilling your beer with ice, be sure to put some under the keg. The tap draws the beer from the bottom of the keg.Thanks
- Some kegs won't have a gas cylinder to help dispense beer. Instead, they will have a vertical pump. Pump once after you change a keg. If the beer doesn't flow or comes out flat, pump again until you achieve the desired result.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Kegs and CO2 canisters contain pressurized contents. Be careful when changing them.Thanks
- Taps aren't interchangeable with kegs of different beer brands. Make sure you replace an empty keg with the same brand.Thanks
Advertisement
Things You'll Need
- Full keg
- Refrigeration unit or tub of ice
- CO2 canister
- Spanner
- Plastic washer
References
About This Article
Article Summary
X
To change a keg, first, turn off the CO2 line, if there is one, then lift the coupler handle at the base of the tap and rotate it counter-clockwise to remove the empty keg. When you're ready to connect the new keg, remove the plastic cap and line up the lugs on the tap with the slots in the well of the keg. Then, keeping the coupler handle raised, fit the tap onto the keg and twist it clockwise until it's snug. From here, you can secure the new keg by pressing the coupler handle down to its locked position. Before you use the new keg, make sure to turn the CO2 canister back on and open the faucet to expel excess foam. For more advice, including how to change a keg's CO2 canister, keep reading!
Did this summary help you?
Thanks to all authors for creating a page that has been read 186,312 times.
Advertisement
