Download Article
Download Article
Electrical contacts may get dirty with normal use, which can affect an item’s performance. You can’t clean an electrical contact with water, but there are some products that are safe and effective. Try cleaning the contacts with a micro-brush and contact cleaning solution if it’s not too dirty. If the item is extra dirty, you will need to get a special cleaning product or kit.
Steps
-
Apply a cleaning solution to a microbrush. Micro-brushes are tiny, disposable cleaning tools that are used to reach into small spaces, such as cell phone charger slots. These are usually available at electronic and office supply stores, or you can also buy them online. Dip the brush into your cleaning solution. You can use a cleaning solution meant for cleaning electrical contacts, or try a household product, such as: [1] X Research source- Rubbing alcohol
- Acetone
- White vinegar
- WD-40
- Nail polish remover
Tip : For hard to reach electrical contacts, you might also try using a can of concentrated air or a pressurized contact cleaner. These can penetrate where even a microbrush won’t fit.
-
Insert the brush into the contact or wipe it off. Make sure that the item is unplugged before you start cleaning it. Then, take the part of the brush that you dipped into your solution and insert it into the electrical contact slot, or wipe the brush across the surface of the contact if it is exposed. [2] X Research source- Make sure that the brush is not dripping with the solution. If it is, dab it off on a paper towel before cleaning the contact.
Advertisement -
Allow the item to dry completely. After you finish wiping the contact and you are satisfied that it is clean, discard the microbrush and place the item on a flat surface. Allow it to dry for at least 1 hour or until you are certain it is completely dry. [3] X Research source- Alcohol dries quickly, so it should be dry in a matter of minutes, but a cleaning solution, vinegar, or nail polish remover might take longer to dry.
Advertisement
-
Read the manufacturer’s instructions for use. If you have purchased a special kit to clean your electrical contacts, read through all of the instructions that came with it. The kit may include multiple types of solution, which may only be used on certain types of metal, such as gold, silver, or copper. [4] X Research source- The instructions should also provide information on how long to leave the product on before scrubbing or wiping it off.
-
Use the provided cleaning tools to remove dirt and debris. It’s best to start by getting as much dirt and debris off of the contacts as you can without using the solution. Choose a brush that will fit into the slot if the contact is not exposed, or select any brush to clean an exposed contact. [5] X Research source- The kit’s instructions might also specify which brushes are meant for certain types of contacts.
-
Apply the solution as indicated by the instructions. Make sure that the item is unplugged from its power source first. Then, use the applicator brush included with the kit to apply contact cleaning solution to the contact. Cover the entire surface of the contact with the cleaning solution. [6] X Research source- Once the contact is completely covered, check the time and leave the solution on for the amount of time indicated by the kit. This may range from a few minutes to a few hours depending on how dirty the contacts are.
- For example, you might need to leave the solution on overnight if the contacts are extra dirty. [7] X Research source
-
Wipe off the surface of the contacts with a brush or lint-free cloth. After the solution has been sitting for the required amount of time, wipe or brush it off one more time. You can either use a brush to wipe away any remaining debris from the inside of a contact’s slot, or use a lint-free towel to wipe off an exposed contact. [8] X Research source- If the contact still appears dirty, repeat the process.
Tip : If there is still a noticeable amount of debris on the item, you might also try rubbing the contact with an eraser. You can use a small pencil eraser or a large eraser depending on the side of the contact. [9] X Research source
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- You may want to put on a pair of vinyl gloves before you start cleaning the item. This will protect the contacts from any oils on your skin.Thanks
- Always use a non-flammable substance from a known brand so you don't risk any injuries.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Never submerge an electrical item in water or in any other solution.Thanks
- Never clean an electrical contact while it is still plugged in.Thanks
Advertisement
References
- ↑ https://mechanicbase.com/electric/how-to-clean-car-electrical-contacts/
- ↑ https://trdsf.com/blogs/news/cleaning-electrical-connections-a-guide-to-electrical-contact-cleaners
- ↑ https://trdsf.com/blogs/news/cleaning-electrical-connections-a-guide-to-electrical-contact-cleaners
- ↑ https://trdsf.com/blogs/news/cleaning-electrical-connections-a-guide-to-electrical-contact-cleaners
- ↑ https://trdsf.com/blogs/news/cleaning-electrical-connections-a-guide-to-electrical-contact-cleaners
- ↑ https://www.youtube.com/watch?v=bOt6ojo7Jfo&feature=youtu.be&t=86
- ↑ https://www.youtube.com/watch?v=bOt6ojo7Jfo&feature=youtu.be&t=120
- ↑ https://www.youtube.com/watch?v=bOt6ojo7Jfo&feature=youtu.be&t=130
- ↑ https://www.youtube.com/watch?v=hMSoghy-E7M&feature=youtu.be&t=40
About This Article
Thanks to all authors for creating a page that has been read 140,124 times.
Advertisement
