How to Clean a Fitbit

PDF download Download Article
PDF download Download Article

Fitbit devices are tremendous for encouraging activity, but they get dirty very quickly. Every usage introduces sweat, dirt, and oil that stains the band, clogs the charger ports, and can lead to skin irritation. Wipe off the Fitbit as soon as you take it off. Also, use cotton swabs and rubbing alcohol to clean the tracker and its charging ports. Finally, treat the band with rubbing alcohol or a soap-free cleanser.

Method 1
Method 1 of 3:

Cleaning the Tracker

PDF download Download Article
  1. The tracker on some versions, including the Blaze, can be pushed out gently from behind. Others, including the Flex 2, require you to undo the band clasp first. [1]
    • Consult your owner’s manual for instructions on how to remove your version’s tracker.
  2. Cotton swabs and rubbing alcohol can be found at general stores and drugstores. Water should not be used, since it can get inside the tracker and damage it. Also, abrasive scrubbers should not be used. [2]
    Advertisement
  3. Apply the rubbing alcohol with the cotton swab. Don’t use a lot at any time. While rubbing alcohol does dry quickly, too much of it can still damage the tracker.
  4. Remove leftover moisture with a soft cloth. Make sure all moisture is removed before returning the tracker to the band. The “pebble” tracker in the Flex 2 can be dried completely with a paper towel. Avoid using paper towels or glass cleaners on tracker screens.
    5. Advertisement
Method 2
Method 2 of 3:

Maintaining the Charging Port

PDF download Download Article
  1. Rubbing alcohol can be found at any general store or drugstore. Water should not be used, since it can damage the electrical parts inside the tracker. Use a toothpick or old toothbrush rather than a metal scrubber so you don’t scrape the tracker’s plating.
  2. Locate the gold-colored charging port on the back of the tracker. Scrub using the toothbrush or use the toothpick to pick out any debris you find. [3]
  3. Cotton swabs (Q-tips) can be purchased alongside rubbing alcohol at general stores and drugstores. Again, avoid introducing water into the electrical circuit or using abrasive scrubbers that damage the metal.
  4. Clean out both ends of the charging cable. Push the swab into the openings and brush off the pins inside them. Make sure all debris is removed before you finish. [4]
  5. Excess moisture can be removed on the charge port by using a soft cloth or tissue. Otherwise, the ports and pins should look dry within a few minutes. Then it is safe to charge your tracker again.
    6. Advertisement
Method 3
Method 3 of 3:

Cleaning the Band

PDF download Download Article
  1. After each use, take a microfiber cloth and wipe off the entirety of the band. This will prevent buildup of dirt and oils that damage the band and irritate your skin.
  2. For stuck-on debris, a dampened microfiber cloth can help. Make sure the cloth is only slightly damp, not dripping. Use it to wipe over the band’s surface. This can be used on any band type, including leather and metal.
    • Excess water will damage leather and tarnish metal, so minimize your water usage as much as possible.
  3. Oils, deep stains, and smells on elastomer and nylon bands can be treated with a cleanser such as Cetaphil Gentle Skin or Aquanil. Place a small amount on the tip of your finger and spread it over the band. Afterwards, wipe off the band again with a dampened towel. [5]
    • Nylon bands can be treated with a neutral pH liquid detergent such as Dawn and washed in cold water.
    • Treat leather bands with a leather cleaner and conditioner. This helps remove stains as well as protect against new ones.
  4. Use an old toothbrush to loosen stubborn debris and tough stains. These brushes are soft enough that they won’t wear out the band’s fibers. You may also dampen a cotton ball in rubbing alcohol and wipe down the band. [6]
  5. Pat away as much moisture as you can with a microfiber cloth. Water must not be allowed to sit on metal or leather. Once this is done, place the band aside in a safe location. Keep it out of direct sunlight, heat, and humidity. [7]
    6. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      • Keep the Fitbit away from water. Use rubbing alcohol or a slightly dampened towel when cleaning to minimize water exposure.
        Thanks
        Helpful 3 Not Helpful 1
      • Don’t allow the band to rest on dark-colored clothing. The coloring causes dark spots on the Fitbit band.
        Thanks
        Helpful 4 Not Helpful 0
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      You Might Also Like

      How to
      Locate, Remove & Clean a Dirty MAP Sensor
      How to
      Clean a Roborock Sensor
      How to
      Clean a Mousepad: Fabric, RGB, & Plastic
      The Best Ways to Clean Your Headphones and Earbuds
      How to
      Clean Electrical Contacts
      How to
      Clean and Maintain an iPad Screen
      3 Helpful Ways to Keep Dust Out of Your Computer
      How to
      Clean a Typewriter
      How to
      Clean a Projector Screen
      How to
      Clean a PopSocket
      Advertisement

      References

      1. ↑ https://help.fitbit.com/articles/en_US/Help_article/2084
      2. ↑ https://help.fitbit.com/articles/en_US/Help_article/2005
      3. ↑ https://help.fitbit.com/articles/en_US/Help_article/2005
      4. ↑ https://help.fitbit.com/articles/en_US/Help_article/2005
      5. ↑ https://www.wareable.com/fitbit/fitbit-flex-2-essential-tips-and-tricks
      6. ↑ https://www.fitbit.com/product-care
      7. ↑ https://www.wareable.com/fitbit/fitbit-flex-2-essential-tips-and-tricks

      About This Article

      Article Summary X

      To clean a Fitbit, start by removing the tracker from the band. Dampen a cotton swab with rubbing alcohol and wipe the surface of the tracker gently, then dry it with a microfiber cloth and set it aside. Use a toothpick dipped in rubbing alcohol to clean the charging ports, then dip a Q-tip in alcohol, swab the charging cable, and dry both pieces off with a tissue. Lastly, wipe down the band with a dampened microfiber cloth. If you need to, use a little soap-free cleanser to scrub dirty fabric bands. If you want to learn more, like how to scrub the Fitbit with a toothbrush to clean it, keep reading the article!

      Did this summary help you?
      In other languages
      Thanks to all authors for creating a page that has been read 58,725 times.

      Did this article help you?

      Advertisement