PDF download Download Article
An easy guide to keeping your whetstone clean and ready to use
PDF download Download Article

Cleaning your sharpening stone regularly will ensure that it works well and doesn’t get clogged. You can easily flush out any metal fillings that embed themselves in the stone with honing oil. You can also remove oil and dirt from an older sharpening stone with WD-40 and steel wool. Make sure to flatten your sharpening stone at least every 10 sharpening sessions to keep it even and to remove stubborn, embedded metal fillings.

Quick Ways to Clean a Sharpening Stone

Rub a small amount of honing oil on the stone with a soft toothbrush, using circular motions. Use a damp cloth to wipe away metal flecks. Rinse thoroughly with water, then dry with a paper towel. For more serious dirt and grime, coat the stone in WD-40 and scour gently with steel wool. Wipe with a damp paper towel.

Method 1
Method 1 of 3:

Flushing out Mineral Filings

PDF download Download Article
  1. Honing oil is a mineral oil that is commonly used in machine shops to carry away metal flecks from stone. [1] Apply honing oil to your sharpening stone with your finger or a soft toothbrush in small, circular motions. Continue rubbing until you see metal flecks rise up from the pores of the stone. [2]
    • Honing oil can also be used to provide lubrication during the sharpening process.
    • Purchase honing oil in hardware stores or online.
    • Use honing oil to flush out your sharpening stone whenever you see metal flecks embedded in the surface, as they may reduce its effectiveness.
  2. Watermark wikiHow to Clean a Sharpening Stone
    Wet a clean cloth or paper towel and wring it out. Gently wipe the surface of the sharpening stone with it. Be sure to remove all the metal filings that emerged from the stone. [3]
    Advertisement
  3. Watermark wikiHow to Clean a Sharpening Stone
    Washing the sharpening stone will remove any remaining metal filings and debris from your stone. Run the stone under warm water for 1-2 minutes to ensure that it is clean. Dry the stone with a clean, dry cloth or paper towel. [4]
    • Do not use soap or anything other than water to clean it.
  4. Advertisement
Method 2
Method 2 of 3:

Removing Dirt and Grime

PDF download Download Article
  1. Watermark wikiHow to Clean a Sharpening Stone
    WD-40 is a specially-formulated oil spray with numerous uses, such as penetrating tough surfaces. Spray WD-40 onto the surface of your sharpening stone. Make sure that the surface is entirely coated. [5]
    • Be sure to use this spray in a well-ventilated area.
  2. Watermark wikiHow to Clean a Sharpening Stone
    To break up tough, caked on oil or debris, you will need to use an abrasive tool like steel wool. Rub a piece of 0000 grade steel wool over the surface of your stone. Continue until you see oil and debris start to come off of the surface. [6]
    • This method will apply mostly to older sharpening stones that have not been used frequently.
  3. Watermark wikiHow to Clean a Sharpening Stone
    After scouring the stone, remove the remaining dirt, oil, and WD-40. Wet a clean cloth or paper towel and wring it out. Wipe down the stone thoroughly. [7]
    • Repeat the process if any dirt or grease remains on the stone.
    • Scour your sharpening stone whenever oil, grease, or dirt begin to build up on the surface and dull its effectiveness.
  4. Advertisement
Method 3
Method 3 of 3:

Flattening Your Sharpening Stone

PDF download Download Article
  1. Some sharpening stones will come with their own flattening plate, a tool used to even out their surface. Moisten your sharpening stone thoroughly with water or oil. Gently drag the flattening plate back and forth over the surface of the stone until it looks even and no embedded metal filings are visible. [8]
    • If you are flattening a synthetic sharpening stone, which is usually grittier and coarser than natural stones, wet it with honing oil rather than water. [9]
    • If your sharpening stone did not come with a flattening plate, you can purchase a silicon-carbide flattening plate at a hardware store or online.
  2. Adhere a self-adhesive piece of 100-grit wet-dry sandpaper to a flat surface like a small, thick piece of glass. Wet your sharpening stone with oil or water and rub it over the sandpaper. Sand the stone until it looks flat and you see no sign of metal filings embedded in it. [10]
    • To hold the stone in place while you flatten it, consider placing a rubber mat underneath the small, flat surface you are sanding on.
    • You will not be able to flatten your stone properly if you sand it while it is dry.
  3. Watermark wikiHow to Clean a Sharpening Stone
    Wet your sharpening stone with oil or water. Run a piece of 400-grit sandpaper over it firmly to remove large grooves or scratches. This should in turn remove any filings or debris lodged in the grooves and prevent any other buildup. [11]
  4. After prolonged use, sharpening stones will begin to hollow out in the middle. This may result in rounding the edges of your tools when you sharpen them. Avoid this by flattening your sharpening stone after 10 sharpening sessions, or more often if you wish. [12]
    • To avoid any dishing out of your sharpening stone, flatten it for 15 seconds before each use.
  5. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      About This Article

      Thanks to all authors for creating a page that has been read 121,282 times.

      Did this article help you?

      Advertisement