Download Article
Download Article
When driving nails near edges or ends of hard, brittle, or knotty wood, you may have the misfortune of having a large crack appear, or even a piece of your lumber break out at the edge. There are a few ways of decreasing the likelihood of this happening.
Steps
Download Article
-
Blunt the point of the nail with your hammer. This is done by placing the nail on a hard surface with the point facing up, and tapping the sharp end with your hammer. The nail will then cut its way through the wood grain, rather than wedging a pathway. Though this puts all the material displacement along a single plain, rather than dispersing it all around the point of the nail. [1] X Research source -
Lubricate your nail. For especially hard woods like oak or maple, you may have better luck if you dip the nail in petroleum jelly, which reduces the friction of the driving process, and can decrease the probability of the wood splitting. [2] X Research sourceAdvertisement -
Avoid nailing very near the edge or end of the board. Where end nailing is necessary, angle the nail so that it can be started farther away from the end, but the nail will still get a bite into the other board it is being nailed to. -
Use the smallest diameter nail which will do the job, or hold the workpieces securely. Obviously, a 16d or 20d nail, with its larger diameter, will exert more force on the wood's grain, making the wood more likely to split. -
Pre-drill a hole slightly smaller than the nail's shank diameter. For a 12d nail, about 3 ⁄ 32 inch (0.2 cm) will reduce the pressure of the nail penetration without decreasing the nail's grip on the board. [3] X Research source -
Use wood with sufficient moisture if possible. Very dry wood is more likely to split, since the drier the wood is, the less flexible it will be. [4] X Research source -
Use softwoods where they are suitable for your purposes, rather than hardwoods. Douglas Fir, Southern Yellow Pine, or Lodge pole Pine are less likely to split than are Oak, Birch, or Maple. [5] X Research source -
Avoid nailing through, or very near knots in the lumber. Knots are usually formed by heartwood , which is harder and less flexible than sapwood . -
Back any nail out if a crack begins to appear while driving it. A tiny crack is a sure indication the wood will split if you continue, possibly ruining a board if it is being used for trim work. You may have to look at choosing another location for your nail, further from the end or edge of the board, or pre-drill a hole for a wood screw or other fastening method. -
Finished.
Advertisement
Community Q&A
Search
-
QuestionWhat size nails (diameter and length) should I use for installing shoe moulding?Community AnswerI would use ones that are small in diameter with small, rounded heads. Make sure they are long enough to grip into something solid after they've penetrated the shoe moulding (and possibly drywall). You want the penetration to be at least the thickness of your shoe moulding, but two times as much would be better. You can greatly reduce splitting with any nail by taking your hammer and flattening the pointed end with a few gentle strikes. Then, rather than separating the wood fibers, you'll be punching them out in the shape of that nail which reduces the splitting.
-
QuestionShould I be concerned about wood splitting at a later date when using soft wood?Community AnswerNot overly.
-
QuestionIs aged wood hardwood?Community AnswerNo. Hardwood is wood from broad-leaved temperate and tropical forest trees. Softwood is from gymnosperm trees such as conifers. Old-growth conifers like Southern Yellow Pine heartwood have a hardness scale similar to hardwoods. Hardness scale is different than hardwood.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Do not use wood which has excessive moisture, since it will shrink as it dries, and even wood that appears sound may crack as it shrinks.Thanks
- Choose wood with a good moisture content, softwoods are typically kiln dried to about 11-14% moisture for stability and minimal shrinkage.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Things You'll Need
- Hammer, nails, and lumber
- Drill with small drill bits (optional)
References
- ↑ https://www.askthebuilder.com/preventing-wood-splitting-video/
- ↑ https://home.tips.net/T012530_Keeping_Nails_from_Splitting_Wood.html
- ↑ https://www.woodworkingnetwork.com/knowledge-center/wood-dr/splits-caused-nails-and-screws
- ↑ https://extension.purdue.edu/extmedia/FNR/FNR-163.pdf
- ↑ https://www.woodworkingnetwork.com/knowledge-center/wood-dr/splits-caused-nails-and-screws
About This Article
Thanks to all authors for creating a page that has been read 154,150 times.
Advertisement
