PDF download Download Article PDF download Download Article

Air tanks are filled by using air compressors, which you can often find at gas stations and truck stops. Once you hook the compressor’s hose to the tank, air will begin flowing into it. Keep an eye on the pressure gauge so you can detach the hose when the tank is full. Then, use and store the tank properly to ensure that you can reuse the tank whenever you need it.

Method 1
Method 1 of 3:

Putting Air in the Tank

PDF download Download Article
  1. Full-service gas stations or truck stops are the most common locations that have air compressors. You can use the same pump motorists use to inflate the tires on their vehicles.
    • Inspect your air tank for damage before filling it, and get a new one if you see any cracks or rust.
    • You may also be able to get your tank filled at scuba shops, paintball locations, and some sporting goods stores.
    • You can use your own air compressor . You can purchase one at a home improvement store.
  2. Set the tank on the ground, then pull the compressor hose down to the metal valve on top of the tank. It is next to the pressure gauge and usually made of brass, so it is hard to miss. Fit the hose’s nozzle over the spout on the back end of the fitting. [1]
    • Attach the air hose directly to the spout. It should fit right over it with no space between them.
    • Avoid placing the compressor hose where the tank’s air hose attaches on the opposite end of the fitting.
    Advertisement
  3. Operate the air compressor by following the directions on the pump. Normally, you will need to press a button to activate the compressor. The hose will usually have a trigger you need to pull to begin pumping air.
    • The amount of time needed to fill the tank depends on the tank’s size. Set aside about 20 minutes in order to fill the the tank completely.
    • Keep the tank’s valve closed. The air will still flow into it.
  4. Make sure you have a clear view of the pressure gauge. As the tank fills, the gauge’s needle will begin to move. Stop adding air when the needle reaches the labeled red zone on the gauge. [2]
    • Overfilling the tank is dangerous, so never fill it beyond the recommended limit.
  5. Once you are done pumping air, slide the hose off the brass fitting. All you have to do now is place the hose back in its holster and take your tank home!
    • The tank will be heavier now, so be careful when moving it!
  6. Advertisement
Method 2
Method 2 of 3:

Releasing Air from the Tank

PDF download Download Article
  1. The stored air is unsafe to breath and can be flammable. Always release the air outdoors, away from other people. Keep your clothing, hair, and jewelry away from the tank’s hose. Also, keep the tank away from open flames. [3]
    • For their safety, avoid letting children operate the tank.
  2. Slide the air hose over the brass fitting near the pressure gauge. It should fit on the opposite end of the small, ringed spout you used to fill the tank. Connect the hose’s other end directly to the item you wish to inflate. [4]
    • An air hose usually is included with the tank when you purchase it. You can get new hoses at home improvement or auto parts stores.
  3. Look near the brass fitting to find a small, handy wheel. Turn the wheel counterclockwise to open the tank’s valve. You should hear air flowing out of the tank right away.
  4. Air will continue to flow until you close the valve again. Watch the inflatable object closely to ensure it is filled at a safe level. Over-inflated items are liable to burst.
    • When an item is inflated to the correct size, it will feel firm to the touch. It should not bulge or appear near bursting.
  5. Listen closely for any hissing coming from the tank, since this indicates that air is still flowing. Make sure the valve is closed completely. When you’re ready, detach the hose to release any air stuck inside of it.
    • If you plan on storing the tank for a while, stay safe by letting all the air out of it.
  6. Advertisement
Method 3
Method 3 of 3:

Storing the Tank Safely

PDF download Download Article
  1. Dirt and moisture are the main causes of corroded tanks. Store your tank in a shed, closet, or a similar safe area. Improper storage is likely to taint any air left in the tank and rust the insides.
    • Try to keep the tank around room temperature, especially if you left air in it. Cold temperatures can lead to rust.
  2. Store the tank separately from other gases, oil, lighter fluid, and similar materials. Leave the tank uncovered in the storage area. In case of a leak, the tank could cause a fire around flammable materials. It can also explode if the pressure builds up too much.
    • For these reasons, keep the tank away from children and animals.
  3. This is to prevent the tank from breaking down or reaching unsafe pressures over time. Look for a small ring on the brass fitting you use to fill the tank. To release the air, pull the ring back until you hear the air hissing out. Wait for it to stop.
    • For safety, it’s best to drain the tank if you won’t use it for 2 or 3 months. If you still wish to store a tank that has air in it, keep it in a temperature-controlled room.
  4. Make sure the tank is empty before you do this. Then, twist the air hose valve off the tank’s brass fitting and set it aside. Flip the tank over, letting the excess moisture drain out of the fitting. When you’re finished, replace the parts and store the tank in a safe spot. [5]
    • Some tanks have a drainage valve on the bottom end you can unscrew to easily drain out the moisture.
    • Moisture can lead to tank corrosion, so frequent draining helps your tank last longer. Drain it after each use if possible.
  5. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Video

      Tips

      • Use a quality air compressor, such as the ones at a gas station or truck stop, to fill your tank faster.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 79,628 times.

      Did this article help you?

      Advertisement