Download Article
Download Article
Electrical conduit fittings form the outer covering for most electrical wiring from one point to the next. They shield the wires from the external environment so as to make the wire last longer and also to keep humans and pets safe from electric shocks or other such vulnerabilities. Electrical conduits are predominantly made of insulating and sturdy material for optimum functionality. Although it is best suited for a professional electrician to accomplish most electrical conduit fittings, there are some minor ones that you can easily do on your own.
Steps
Download Article
-
Choose the right material for installing electrical conduit fittings: The most preferred material is known as EMT (Electrical Metallic Tubing). EMT is very easy to install as you can effortlessly bend it and assemble it as per your needs. Also, you can conveniently take it off in case your wiring goes wrong somewhere. If you do not have it in your house, you can buy EMT from any of the electrical surplus stores for pretty cheap. [1] X Research source -
Chalk out a wiring plan: Find out the location of the electrical boxes on your wall to trace the route of the conduit. Draw the path from the main power source to the electrical box. [2] X Research sourceAdvertisement -
Measure the amount of conduit that you would need: Make appropriate marks in pencil wherever you think the bends should be, and measure the total length of the conduit that would be needed to finish the entire electrical conduit fittings. Now cut the length that you just measured with a tool called hacksaw. The cut ends are likely to have burrs which can be removed using a deburring tool or with pliers. [3] X Research source -
Make the necessary bends: It is now time to make bends that you had marked on the pipe in the previous step. Owing to the easy flexibility of EMT, this should not be very difficult. Conduit benders come in handy for doing this bending. [4] X Research source -
Attach fittings to the wall: You can use screws and straps with either single or double holes, available at electrical surplus shops, to attach electrical conduit fittings to the wall. [5] X Research source- Secure the conduit within three feet of where it connects to the electrical box.
-
Tape the ends and put the wires in place: Use a widely available fish tape and run it through the entire route of the conduit fittings you just installed. Fix together the ends along with the electrical wires with the same fish tape. Give a finishing touch by pulling all the wire in the pipe in their right place.
Advertisement
Community Q&A
Search
-
QuestionWhat is required to couple two cut pipes?Community AnswerA coupling is required. They come in two types: setscrew for dry applications and compression for wet and damp applications.
-
QuestionAre these steps in accordance with the PEC?Community AnswerFor the most part, yes. However, you should never hang a strap as shown in the image. The screws securing the strap should be under the pipe when running horizontally, not above.
-
QuestionWhat is the appropriate spacing of the straps?Community AnswerThe straps should be no more than 10 feet apart along the conduit and no more than three feet from any coupling or fitting.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- While bending the conduit, you are going to cut off some length from the total length of the conduit needed to trace the path. Keep a 5 inches (12.7 cm) margin for each 90 degree bend that you make.Thanks
- Make accurate measurements or you could cut the wrong conduit length.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- If you are working on electrical wires that are attached to a power source, do remember to turn it off before you begin with your fittings. And if the wires are not already attached to the electrical supply, do not make attachments without first turning off the power source.Thanks
Advertisement
Things You'll Need
- EMT conduit
- Conduit bender
- Electrical boxes
- Elbows
- Setscrew couplings
- Single-hole or double-hole straps screws
- Offset fittings
- Setscrew
- De burring tool
- Hacksaw
- Screwdriver
- Electrical fish tape
- Electrical tape
- Tape measure
- Pencil
References
- ↑ https://www.familyhandyman.com/electrical/wiring/how-to-install-surface-mounted-wiring-and-conduit/
- ↑ https://www.familyhandyman.com/electrical/wiring/how-to-install-surface-mounted-wiring-and-conduit/
- ↑ https://www.bhg.com/home-improvement/electrical/how-to-install-metal-conduit/
- ↑ https://www.youtube.com/watch?v=PJOTR4MtHek
- ↑ https://www.bhg.com/home-improvement/electrical/how-to-install-metal-conduit/
About This Article
Thanks to all authors for creating a page that has been read 245,059 times.
Reader Success Stories
- "It affirmed and as well suggested some tenets of electrical conduit placement and usage."
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"It affirmed and as well suggested some tenets of electrical conduit placement and usage."
"It is reliable article that allows quick learning."
